Messages in parameter_settings
[2017-07-21 10:14:24]
gcbrent :
@gcbrent has joined the channel
[2017-07-21 10:14:25]
gcbrent :
set the channel description: To discuss in one place the various parameter settings people are testing
[2017-07-21 10:15:11]
gcbrent :
[2017-07-21 10:16:45]
gcbrent :
For full manual mode(acro)
[2017-07-21 10:17:12]
solution :
@solution has joined the channel
[2017-07-21 10:18:52]
gcbrent :
[2017-07-21 11:15:27]
goof :
@goof has joined the channel
[2017-07-21 11:18:41]
goof :
For P4, maybe Mavic I don't have one...
`g_config_engine_idle_level 1`
`g_config_engine_idle_time 1`
`g_config_engine_stand_by_level 2`
Slows down the idle speed when it's on the ground so a stiff breeze won't blow it over. Needs further testing, I'll have a look tomorrow when it's light out
[2017-07-21 11:45:40]
tomgt :
@tomgt has joined the channel
[2017-07-21 11:46:12]
tomgt :
Is it safe to fly p4p above 500m
[2017-07-21 11:46:29]
tomgt :
I heard autolanding initiation and battery low error qhen above 500
[2017-07-21 11:46:54]
goof :
generally doesn't happen until you're around 1KM
[2017-07-21 11:47:21]
tomgt :
So is it dangerous?
[2017-07-21 11:47:29]
goof :
as long as you watch your time bar at the top and descend before it hits the red you should be ok
[2017-07-21 11:47:41]
goof :
the worst that happens is it start slowly coming down
[2017-07-21 11:47:54]
tomgt :
Is there any fix to that?
[2017-07-21 11:47:58]
tomgt :
Slow decsendingv
[2017-07-21 11:48:12]
goof :
supposedly tell the aircraft it's not using a DJI battery
[2017-07-21 11:48:18]
goof :
in Assistant
[2017-07-21 11:48:34]
goof :
but then you will need to keep a very close eye on the battery yourself
[2017-07-21 11:48:46]
tomgt :
But will the RTH WORK ?
[2017-07-21 11:48:54]
goof :
recommended only for high altitude attempts
[2017-07-21 11:48:58]
goof :
RTH will work
[2017-07-21 11:49:03]
goof :
auto RTH might not though
[2017-07-21 11:49:10]
tomgt :
So what is the problem?
[2017-07-21 11:49:13]
tomgt :
The con
[2017-07-21 11:49:26]
tomgt :
Wont it show the battery level?
[2017-07-21 11:49:32]
goof :
say you're 5KM away and you lose connection
[2017-07-21 11:49:57]
goof :
auto RTH on signal loss kicks in and takes the drone behind a tree or something
[2017-07-21 11:50:08]
goof :
and you can't get it connected again before the battery dies
[2017-07-21 11:50:23]
goof :
if you have non DJI battery set it'll fall out of the sky
[2017-07-21 11:50:31]
goof :
since battery RTH won't kick in
[2017-07-21 11:50:37]
goof :
and land it for you
[2017-07-21 11:50:59]
tomgt :
So if you lose connection, youre done
[2017-07-21 11:51:13]
goof :
if you can't get it connected again, yeah
[2017-07-21 11:51:32]
goof :
usually not very hard ot get some elevation and get a better signal to the drone for reconnection though
[2017-07-21 11:51:34]
goof :
in most cases
[2017-07-21 11:51:44]
tomgt :
What about going 1000m
[2017-07-21 11:51:52]
tomgt :
With dji battery
[2017-07-21 11:52:23]
goof :
well you get up there, take three pictures and then the drone keeps trying to descend on you...
[2017-07-21 11:52:31]
goof :
or you mean 1KM away?
[2017-07-21 11:52:35]
tomgt :
No
[2017-07-21 11:52:40]
tomgt :
What I mean is alltitude
[2017-07-21 11:53:09]
tomgt :
There is a mountain
[2017-07-21 11:53:12]
tomgt :
2000m
[2017-07-21 11:53:19]
tomgt :
I am planing to go up to 1000m
[2017-07-21 11:53:57]
goof :
it's up to you
[2017-07-21 11:54:23]
tomgt :
Is it dangerous if descending is slow?
[2017-07-21 11:54:29]
goof :
if the critical battery message proves ***really*** annoying then set non-dji for your next flight
[2017-07-21 11:54:39]
goof :
but
[2017-07-21 11:54:39]
goof :
not inherently
[2017-07-21 11:54:47]
goof :
sometimes it gets stuck like that
[2017-07-21 11:55:19]
goof :
if you really are at a low battery level and it gets stuck coming down at 2m/s, from >1KM that's going to take a while....
[2017-07-21 11:55:33]
tomgt :
Not that way
[2017-07-21 11:55:41]
tomgt :
Going up having %50
[2017-07-21 11:55:47]
tomgt :
And coming down instantly
[2017-07-21 11:56:17]
goof :
you shouldn't be starting a flight without a fully charged battery anyway....
[2017-07-21 11:56:29]
goof :
especially if you're trying for altitude
[2017-07-21 11:56:37]
tomgt :
No what I mean is
[2017-07-21 11:56:49]
tomgt :
Im up 1000m having %50
[2017-07-21 11:56:53]
tomgt :
And coming down
[2017-07-21 11:57:18]
goof :
having 10 m/s descent speed is recommended
[2017-07-21 11:57:28]
goof :
with a bit of forward speed of course
[2017-07-21 11:57:38]
goof :
don't want VRS
[2017-07-21 11:57:45]
goof :
will need another parameter for that: <https://flyflydrones.com/pages/custom-flight-parameters>
[2017-07-21 11:58:20]
goof :
`g_config_mode_sport_cfg_vert_vel_down` can go down to at least 10
[2017-07-21 11:58:53]
tomgt :
Is it safe to change motor speed
[2017-07-21 11:58:53]
tomgt :
?
[2017-07-21 11:59:21]
goof :
it doesn't affect motor speed, it just lets you descend faster
[2017-07-21 12:00:01]
goof :
afaik you can't change max motor speed, only speed limits and tilt angles etc
[2017-07-21 12:00:03]
tomgt :
And battery decreases faster?
[2017-07-21 12:00:19]
goof :
only if you change ascent speed
[2017-07-21 12:00:27]
goof :
or fly like a maniac
[2017-07-21 12:00:39]
goof :
descending fast uses less battery than hovering
[2017-07-21 12:01:09]
tomgt :
Is it only used on sport mode?
[2017-07-21 12:01:22]
tomgt :
In*
[2017-07-21 12:02:05]
goof :
I think so
[2017-07-21 12:02:49]
tomgt :
I have a p4p
[2017-07-21 12:02:52]
tomgt :
Its unstable
[2017-07-21 12:03:05]
tomgt :
Its drifting left and right with little wind
[2017-07-21 12:03:21]
goof :
how far
[2017-07-21 12:03:36]
tomgt :
I can notice it on the screen
[2017-07-21 12:03:58]
tomgt :
not much
[2017-07-21 12:04:00]
goof :
so it flies in a gentle curve?
[2017-07-21 12:04:02]
tomgt :
But half a meter
[2017-07-21 12:04:08]
goof :
at high speeds?
[2017-07-21 12:04:12]
tomgt :
Slightly left
[2017-07-21 12:04:15]
tomgt :
And slightly right
[2017-07-21 12:04:23]
tomgt :
Not high speed
[2017-07-21 12:04:26]
tomgt :
Normally
[2017-07-21 12:04:31]
tomgt :
When its in the sky
[2017-07-21 12:04:34]
tomgt :
And not moving
[2017-07-21 12:04:56]
goof :
half a metre's not that much....
[2017-07-21 12:05:04]
tomgt :
Is it normal?
[2017-07-21 12:05:28]
goof :
probably
if you're in the sky you might not have the high-precision VPS to hold it stable
[2017-07-21 12:05:46]
tomgt :
Is there anyway to fix it?
[2017-07-21 12:06:00]
goof :
fly lower so VPS is active
[2017-07-21 12:06:16]
goof :
half a metre on GPS only is really not much
[2017-07-21 12:06:31]
tomgt :
Even at low altitudes
[2017-07-21 12:06:33]
tomgt :
The same
[2017-07-21 12:06:37]
tomgt :
I had mavic
[2017-07-21 12:06:41]
tomgt :
It was solid stable
[2017-07-21 12:07:01]
goof :
you can try calibrating the VPS cameras maybe
[2017-07-21 12:07:10]
tomgt :
How?
[2017-07-21 12:07:12]
goof :
with the DJI Assistant 2
[2017-07-21 12:07:28]
tomgt :
Vision positioning ?
[2017-07-21 12:07:35]
goof :
yes
[2017-07-21 12:07:39]
goof :
<https://youtu.be/mYSqz7R5zwI>
[2017-07-21 12:09:22]
tomgt :
You think its gonna fix it?
[2017-07-21 12:10:03]
goof :
it might
[2017-07-21 12:10:05]
goof :
it might not
[2017-07-21 12:10:18]
goof :
if you've never done that before it's not a bad idea though
[2017-07-21 12:10:36]
goof :
also make sure the cameras are clean
[2017-07-21 12:11:02]
tomgt :
Thank you goof!
[2017-07-21 12:11:48]
goof :
[nolimitdronez.com](http://nolimitdronez.com)
[2017-07-21 12:28:40]
tomgt :
Thank you
[2017-07-21 12:28:47]
tomgt :
What does the tilt parameter change?
[2017-07-21 13:49:29]
goof :
how far the aircraft is allowed to tilt
[2017-07-21 13:49:47]
goof :
by consequence, how fast it'll go
[2017-07-21 16:00:41]
dingop :
@dingop has joined the channel
[2017-07-21 16:07:32]
andreasnofear :
@andreasnofear has joined the channel
[2017-07-21 19:03:50]
gcbrent :
@ender
[2017-07-21 19:03:58]
ender :
@ender has joined the channel
[2017-07-21 21:14:06]
ender :
? 60degrees afair, but 50 i like better :slightly_smiling_face:
[2017-07-21 22:00:19]
asoka :
@asoka has joined the channel
[2017-07-21 23:02:09]
gcbrent :
50 tilt I find is ample
[2017-07-22 01:36:32]
hotelzululima :
@hotelzululima has joined the channel
[2017-07-22 06:12:38]
tomgt :
Can someone show me a pic of 60 degree angle pov?
[2017-07-22 07:28:10]
capra_vecinului :
@capra_vecinului has joined the channel
[2017-07-22 07:44:26]
goof :
@digdat0 no dice today with your battery trick for high altitude
[2017-07-22 07:44:51]
digdat0 :
@digdat0 has joined the channel
[2017-07-22 07:45:06]
goof :
on the P4
[2017-07-22 07:45:33]
goof :
setting battery to non DJI, LED only warnings on both levels, disabled smart RTH in the GO app
[2017-07-22 07:45:51]
goof :
still complains about critical battery over 1600M ish
[2017-07-22 07:46:32]
goof :
actual battery level was around 60-70% at the time
[2017-07-22 07:47:25]
goof :
perhaps it's a Mavic - only trick
[2017-07-22 08:39:41]
tomgt :
Goof
[2017-07-22 08:39:59]
tomgt :
I went to 1040m with dji battery
[2017-07-22 08:40:04]
tomgt :
Had no problem
[2017-07-22 08:40:18]
tomgt :
When does the critical battery error appear?
[2017-07-22 09:03:31]
goof :
Any time your time remaining bubble hits the red line at the top
[2017-07-22 09:03:50]
goof :
starting to think it might be triggered by the GO app, not the aircraft
[2017-07-22 10:27:06]
sincoder :
@sincoder has joined the channel
[2017-07-22 21:30:54]
tyras :
@tyras has joined the channel
[2017-07-22 21:39:06]
tyras :
I cant seem to find nfz parameters on p4 v1.02.0602
[2017-07-22 21:39:12]
tyras :
How to remove it on that version?
[2017-07-22 22:23:52]
tyras :
?
[2017-07-23 01:20:43]
goof :
it might be a 2.00.0106 thing
[2017-07-23 01:21:28]
goof :
I know there are a few parameters in the no limit drones app that are greyed out on 1.02.0602, so I presume they're just not there
[2017-07-23 02:16:36]
czokie :
@czokie has joined the channel
[2017-07-23 04:40:00]
tyras :
How to fix it goof any ideav
[2017-07-23 04:40:03]
tyras :
?
[2017-07-23 05:24:33]
goof :
well if it's not there you can't remove it
you can try 2.00.0106 FW and see if
1. Is it there and can you remove it
2. Does that actually work?
3. Does the bird actually fly properly still?
[2017-07-23 05:24:58]
goof :
2.00.0106 is causing major issues for a lot of people, very unstable flight characteristics
[2017-07-23 05:25:15]
goof :
at least you can come back to 1.02.0602 with DUMLdore if there are problems though
[2017-07-23 05:59:52]
tyras :
I checked both
[2017-07-23 06:00:02]
tyras :
It does not exist in both
[2017-07-23 06:00:50]
goof :
strange
[2017-07-23 06:00:51]
goof :
hmm
[2017-07-23 06:02:25]
goof :
I know I could only remove the NFZ on 2.00.0106 with @coldflake's app
[2017-07-23 06:02:25]
goof :
I'm not sure what the actual parameters are called to do it manually
[2017-07-23 06:34:26]
tyras :
Where to downlod the coldflake's app?
[2017-07-23 06:34:37]
tyras :
Can you please give me some link
[2017-07-23 06:59:11]
nembrok :
@nembrok has joined the channel
[2017-07-23 07:54:43]
rulppa :
@rulppa has joined the channel
[2017-07-23 08:11:21]
kiteboy :
@kiteboy has joined the channel
[2017-07-23 11:11:34]
tyras :
Does the nolimitz fly work on phantom 4 nfz removal?
[2017-07-23 15:04:42]
tyras :
??
[2017-07-23 15:12:35]
guest :
@guest has joined the channel
[2017-07-24 06:35:05]
flystraightcircles :
@flystraightcircles has joined the channel
[2017-07-24 08:28:55]
f3l1x :
@f3l1x has joined the channel
[2017-07-26 22:41:08]
gcbrent :
Someone tried height limit removal on Spark fw500?
[2017-08-04 14:12:27]
rainman :
Does anyone have the wm220.. .cfg files from **Assistant** that they can post or add to my parameters Git? I've tried a zillion different Assistant installs and I never see any wm220.. files in Data\config. I'm trying to verify the differences in param values between Mavic and Spark. (@czokie - this has a few implications for the param list format on the wiki, I think?)
<https://github.com/JD4x4/dji_assistant_parameter_lists>
[2017-08-04 14:32:51]
kilrah :
did you actually connect an aircraft/do an upgrade with said assistant install? it's been said the files are only retrieved from the net when needed
[2017-08-04 14:33:14]
kilrah :
i have 3 in my folder
[2017-08-04 14:52:57]
rainman :
No. I only have a Spark. Can you PM your files to me or something easy? From various snippets out there, I'm pretty sure there are a bunch of differences between Mavic and Spark, both in factory defaults as well as successful mods, so I was hoping to clear the air a bit on the wiki.
[2017-08-04 14:55:02]
kilrah :
already made a pull request to your repo 15 mins ago
[2017-08-04 14:55:11]
rainman :
coolie! ty!!
[2017-08-04 15:45:23]
jan :
@rainman ...fwiw
[2017-08-04 15:46:08]
kilrah :
nice, didn't have 21.19
[2017-08-04 15:54:59]
jan :
:slightly_smiling_face:
[2017-08-04 16:00:41]
jcarlo :
So there is normal mode, sport mode. Any one knows what gentle mode does. I changed it to see if it increased the speed on Pmode while OA is on but no dice
[2017-08-04 16:18:49]
jan :
beginner mode or tripod mode??
[2017-08-04 16:21:23]
jcarlo :
Might be
[2017-08-04 16:29:45]
kilrah :
i believe it's beginner, and/or maybe wifi
[2017-08-04 16:29:52]
kilrah :
OA is "avoid"
[2017-08-04 17:00:14]
jcarlo :
Yes. Played with some parameters to see if I can increase speed on Pmode while OA is on
[2017-08-04 17:01:01]
jcarlo :
I know Pmode speed is increase is OA is disabled
[2017-08-04 17:25:26]
kilrah :
you can most likely increase speed with OA on... but OA won't work correctly, so no point having it on.
[2017-08-04 17:32:30]
jcarlo :
Yeah I should get that in my head. Thanks. I stop trying for now and more flying :grinning:
[2017-08-04 17:51:54]
rainman :
I haven't gotten "in" to all of this enough yet to know the answer to this, but is it possible to mod the Assistant code so that it downloads the files needed to do a f/w upgrade/downgrade .. but stops just short of actually sending the files to the AC? Just a random thought.
[2017-08-04 17:52:40]
kilrah :
that was the first downgrading method used a few months ago. using a VM to capture the state at the right moment.
[2017-08-04 17:53:11]
kilrah :
but you're limited to creating the VM while DJI still distributes the FW you want to back up
[2017-08-04 17:53:28]
rainman :
..with a VM , not actually tweaking the Ass itself, yeah?
[2017-08-04 17:53:52]
kilrah :
well it was fooling the assistant, yes... not "modifying" it
[2017-08-04 17:54:22]
rainman :
I was thinking more along the lines of capturing the stuff from new releases.. ones that no one wants to try yet, lol
[2017-08-04 17:56:01]
mavicbreak :
@rainman try it with older assistant like 1.0.9 and discharge the drone or controller battery level below 50% and start the upgrade. It will fail once the files are downloaded with battery not charged error so the update won’t start. The files are in the firm cache folder so you can extract them.
[2017-08-04 17:57:17]
rainman :
Maybe I can get some time and will try to flash back to my "youth" and see if I can remember how to get my nop on. :dizzy_face:
[2017-08-04 17:58:37]
rainman :
... assuming that stuff still works with the likes of Win10. :stuck_out_tongue_winking_eye:
[2017-08-04 17:59:39]
kilrah :
again no problem to do that with the standard method above
[2017-08-04 18:00:08]
rainman :
ty guys.
[2017-08-04 18:00:57]
kilrah :
what this doesn't give you is the cfg.sig, so you do need the VM snapshot to be able to flash later even if they remove it in the meantime
[2017-08-04 18:01:51]
kilrah :
although with what we know we can likely extract it without an actual flash now - I need to give it a try on my vms
[2017-08-04 18:04:09]
rainman :
Well, as fast as everyone is working around here (and my aversion to be "the 1st to try" stuff), I can wait until new f/w's are "correctly" tweaked by the OG experts. I'm just over here in the corner of the room looking at parameter differences, etc.
[2017-08-04 18:06:56]
rainman :
Lots of background "education" in just the Ass cfg files and differences, etc
[2017-08-05 02:20:20]
rainman :
So.. there's 1100 +- 50 or 75 params available.. and they differ from Ass cfg model file to model file (ie. wm___ 3.2.__.__, etc). Do we know if these file names correlate with the AC f/w versions? I'd guess yes by looking at my Spark data, but I have no idea with Mavic. For example I'm running Spark f/w .300 and what I see in ASS params interface corresponds to Ass .cfg file wm100 v3.2.34.25. The other .cfg file is for wm100 v3.2.37.20 which I'm guessing is for f/w .400 (which I downgraded from).
[2017-08-05 02:20:50]
czokie :
Its listed somewhere in the wiki or on a @hostile git
[2017-08-05 02:21:33]
rainman :
I looked there (both places plus a search here), but that x-ref is for the firmware cfg files, not the Ass .cfg files, afaik.
[2017-08-05 02:31:44]
rainman :
.. and there's 2 Spark cfg files (I don't have .500 stuff) and 4 Mavic cfg files .. kinda points that direction? Would love to know for sure though. Hate talking out of my butt. :scream:
[2017-08-05 02:32:19]
czokie :
@rainman - Suggest asking @hostile in ~general
[2017-08-05 02:32:59]
rainman :
k. It's param related is why I posted here.
[2017-08-05 03:23:17]
czokie :
but he aint here @rainman :slightly_smiling_face:
[2017-08-05 03:31:29]
rainman :
.. I thought he wuz everywhere, lol. especially with the @. Too sleepy now anyway. gonna get some :zzz:
[2017-08-09 10:39:57]
oqradze :
if edit radius parameter from 5000 to 0 I think firmware logic checks this parameter and it is way for bypass NFZ.
[2017-08-09 10:50:27]
goof :
do you have a way to test that?
or if you have no nearby NFZ, increase the radius until it hits one and see what happens :stuck_out_tongue:
[2017-08-09 11:34:00]
oqradze :
@goof no we need decrease radius :slightly_smiling_face: its radius of NFZ poligon. which cames from poligon_db. location this file is in dji go app. It's my mean. maybe I am no true
[2017-08-09 11:34:43]
oqradze :
and I do not have time for testing. :disappointed:
[2017-08-09 15:43:36]
kyokushin :
In p3p mod this parameter with radius was used to set to 1 to remove NFZ <https://github.com/mefistotelis/phantom-firmware-tools/issues/13#issuecomment-294517503>
[2017-08-10 12:04:18]
goof :
anyone managed to manually edit their tilt parameter?
I can't find it with any of my assistant versions, running 1.02.0602 on a P4
[2017-08-10 12:04:27]
goof :
definitely worked the other day o_O
[2017-08-10 12:05:57]
czokie :
Try <http://dji.retroroms.info/howto/parameterhacks>
[2017-08-10 12:10:22]
goof :
ah right
[2017-08-10 12:10:41]
goof :
named differently on different assistant versions
[2017-08-10 12:11:57]
goof :
`g_config_sport_cfg_atti_range` instead of `g_config_mode_sport_cfg_tilt_atti_range` on this version
[2017-08-10 12:38:15]
goof :
@digdat0 `g_config_auto_landing_vel_L<1-2>`
changing these to 0 appears to disable RTH
it gets to the homepoint but won't descend
on my P4 I have 1 set to -0.7 and 2 set to -7
in the simulator it makes the descent much faster, with a lighter landing at the end
I'll have to test it with the aircraft flying tomorrow
[2017-08-14 14:19:51]
rainman :
@carlcox89 .. you can backup your params in Assistant
[2017-08-14 14:19:59]
carlcox89 :
@carlcox89 has joined the channel
[2017-08-14 14:20:57]
carlcox89 :
thanks for invitation
[2017-08-14 14:21:06]
rainman :
.. if you haven't changed them, I can put them into a spreadsheet and edit the wiki
[2017-08-14 14:21:15]
rainman :
np
[2017-08-14 14:21:41]
carlcox89 :
yeah mine are still stock
[2017-08-14 14:21:49]
carlcox89 :
i'll do that right now
[2017-08-14 14:22:21]
rainman :
trying to remember, but I think it's in Tools?
[2017-08-14 14:24:37]
carlcox89 :
i'll figure it out :slightly_smiling_face:
[2017-08-14 14:35:18]
rainman :
Just looked, yeah in tools, menu at top. If you post the text file here and tell me which f/w you are on, I'll put it in the wiki
[2017-08-14 14:36:17]
rainman :
The file is just a text .csv
[2017-08-14 14:38:19]
rainman :
Handy to have after you mod also, since the DUML f/w backup doesn't include these param mods. :open_mouth:
[2017-08-14 14:38:45]
kilrah :
you can make a parameter backup in assistant.
[2017-08-14 14:39:06]
rainman :
.. so if you reload your f/w then you can also restore your mods with the Ass Restore
[2017-08-14 14:39:33]
carlcox89 :
got them
[2017-08-14 14:39:34]
rainman :
yeah.. he's doing that to get defaults before he mods them
[2017-08-14 14:39:47]
carlcox89 :
currently at firmware 0700 - stock params
[2017-08-14 14:40:02]
rainman :
I didn't have Mavic default values for the wiki
[2017-08-14 14:40:13]
kilrah :
restore may or may not work but if you make a bacjup after reset and one after changing your parms it's easy to diff the files to find what you changed
[2017-08-14 14:40:33]
rainman :
coolie! thanx!!
[2017-08-14 14:40:41]
carlcox89 :
no prob. :slightly_smiling_face:
[2017-08-14 14:40:54]
rainman :
You need a hand getting it into a spreadsheet?
[2017-08-14 14:41:13]
rainman :
and correlated to the param display names?
[2017-08-14 14:41:30]
rainman :
they're pretty close as i recall
[2017-08-14 14:42:54]
carlcox89 :
I can put them into a spreadsheet. Just dont know how where to get the display names
[2017-08-14 14:43:40]
kilrah :
throw this in here <https://jsonformatter.curiousconcept.com/>
[2017-08-14 14:43:41]
rainman :
the wiki has the displayed names, but they are also in .cfg files in the Ass Data folder
[2017-08-14 14:43:48]
kilrah :
it miraculously becomes much easier to read :slightly_smiling_face:
[2017-08-14 14:44:17]
kilrah :
and AFAIK these are the names as seen in the assistant, at least they were for every param i used
[2017-08-14 14:44:34]
rainman :
yeah, and there is a json plug-in for notepad++
[2017-08-14 14:44:52]
carlcox89 :
k, i'll look into that :slightly_smiling_face:
[2017-08-14 14:45:06]
carlcox89 :
just happen to see at dji assistant, a param named DJI SDK failsafe action
[2017-08-14 14:45:27]
carlcox89 :
it's set to Hover :open_mouth: . Anyone knows exactly what this is ?
[2017-08-14 14:45:47]
rainman :
I don't.. sorry
[2017-08-14 14:46:27]
rainman :
.. if you find out, add it to the wiki, lol
[2017-08-14 14:47:09]
carlcox89 :
can only think that it maybe related to using other software like litchi and in case of some malfunction the default behavior is 'hover'
[2017-08-14 14:47:24]
carlcox89 :
but that's a long shot
[2017-08-14 14:47:25]
rainman :
that was my WAG too
[2017-08-14 14:47:59]
rainman :
prolly the case tho, i'd bet
[2017-08-14 15:05:15]
rainman :
@carlcox89 do you have a file named wm100 v3.2.30.13.cfg in your Ass Data\CONFIG folder? 3.2.30.13 is one I haven't seen.
[2017-08-14 15:06:29]
rainman :
if so, can I bum it from ya? aka will you post it here? :grin:
[2017-08-14 15:14:36]
carlcox89 :
found it
[2017-08-14 15:15:32]
carlcox89 :
oops.. nope
[2017-08-14 15:15:46]
carlcox89 :
thought it was wm100 but it's wm220
[2017-08-14 15:15:47]
carlcox89 :
sorry
[2017-08-14 15:20:28]
kilrah :
what would it be for? MAYBE the very first spark version, but still...
[2017-08-14 15:22:23]
rainman :
my bad.. it SHOULD indeed be wm220..
[2017-08-14 15:23:14]
rainman :
I've got Spark on the brain! wm220 is Mavic, duh.
[2017-08-14 15:24:15]
rainman :
but it's still a wm220 v3.2.30.13.cfg that I haven't seen (don't have)
[2017-08-14 15:26:57]
carlcox89 :
there you go
[2017-08-14 15:27:14]
carlcox89 :
also here it is: <https://docs.google.com/spreadsheets/d/1Iw_fWpIuUkNkN50tTk4QmxsuC1o1oMnc5KTrGpkMj2g/edit?usp=sharing>
[2017-08-14 15:27:17]
rainman :
ty. sorry for thee confuzion
[2017-08-14 15:27:59]
carlcox89 :
that GDrive link is the stock parameters for 0700
[2017-08-14 15:29:27]
rainman :
Thanx. If you blend your .cfg file and your backup, it will also be a .700 default list.. I'd rather know the source chain, so thanx.
[2017-08-14 15:30:34]
kilrah :
it's in the repo
[2017-08-14 15:30:54]
rainman :
what is? the f/w?
[2017-08-14 15:30:58]
carlcox89 :
what do you mean by blend ? x) (Sorry, English isn't my main language)
[2017-08-14 15:31:05]
rainman :
or the .cfg?
[2017-08-14 15:31:14]
kilrah :
and i still don't understand what you need the cfgs for anyway, better to jsut take a stock bachup from the aircraft, you also get all the names BUT you also gett he default values...
[2017-08-14 15:31:22]
rainman :
match the two files.
[2017-08-14 15:31:31]
kilrah :
no the repo with the cfgs
[2017-08-14 15:31:36]
kilrah :
and why?
[2017-08-14 15:32:44]
rainman :
mine? shite. I AM getting old! The reason I wanted to match .cfg files is because there are some display name differences I think.
[2017-08-14 15:33:07]
carlcox89 :
LOL
[2017-08-14 15:33:12]
carlcox89 :
:smile:
[2017-08-14 15:34:24]
rainman :
And, at least in the case of Spark, not only are some of the Ass display names different, there are omissions between f/w's that I wanted to capture. (I'm just anal is really why, TBT)
[2017-08-14 15:38:42]
kilrah :
things change between FWs yes... but haven't seen any names that differed from assistant and fc
[2017-08-14 15:39:02]
kilrah :
this repo <https://github.com/JD4x4/dji_assistant_parameter_lists/tree/master/config_files>
[2017-08-14 15:40:03]
rainman :
Whew. Can't blame it totally on old.. I just didn't sync my own local repo with GitHub, lol. Been too busy syncing the others. :astonished:
[2017-08-14 16:12:19]
rainman :
@kilrah The differences are usually small, but one example is g_config_control_control_mode[1] in Ass (at least on Spark) = fswitch_selection_1 in backup file. Both are in the .cfg file on the same line. So I thought it best to use the Ass .cfg files as the "translation cross-ref" doc (which is what I think they were intended to be?). Only prob is that the f/w "name" isn't cross-ref'ed anywhere except someplace in the Ass code?
[2017-08-14 16:40:09]
mavicbreak :
@rainman
[2017-08-14 16:41:05]
rainman :
wht up?
[2017-08-14 16:43:13]
mavicbreak :
g_config_control_control_mode[1] is the raw name of the param probably used by the flight controller but if you write the param via websocket (or assistant) fswitch_selection_1 command is sent.
[2017-08-14 16:43:31]
rainman :
interesting
[2017-08-14 16:43:51]
mavicbreak :
In most of the case the raw name equals the name but if you want to write the param you have to use the name.
[2017-08-14 16:44:07]
mavicbreak :
{
“DEFAULT”: 8,
“MAX”: 11,
“MIN”: 0,
“NAME”: “fswitch_selection_1”,
“RAW_NAME”: “g_config_control_control_mode[1]“,
“TYPE”: “uint8_t”,
“VALUE”: “8"
},
[2017-08-14 16:46:06]
rainman :
Well, I was doing the param lists mainly thinking for use with Ass when changing values there, but ..
[2017-08-14 16:46:35]
kilrah :
that's for websockets, but in assistant the raw name is shown
[2017-08-14 16:47:14]
rainman :
.. perhaps I need to label the lists with headers like "Name" and "Raw Name".
[2017-08-14 16:48:02]
mavicbreak :
I think in assistant the name is also shown just in brackets.
[2017-08-14 16:48:18]
rainman :
that way in the relevant wiki sections it can refer to the same list?
[2017-08-14 16:49:17]
rainman :
nott always.. I found some in brackets and some not. I figured someone at DJI just hadn't gotten around to editing all of the .cfg files yet, lol
[2017-08-14 16:49:30]
mavicbreak :
ahh okay.
[2017-08-14 16:50:15]
rainman :
It makes 65 yo eyes go crazy real quick, I can tell ya! (Between differences in what I now know as "Name" & "Raw_Name", plus the different .cfg lists between f/w versions!!)
[2017-08-14 18:45:22]
carlcox89 :
is there any way to change the RTH descent speed ? Can't seem to find anything related
[2017-08-15 07:47:38]
goof :
<https://dji-rev.slack.com/archives/C6BPBBRHR/p1502368695484458>
[2017-08-15 07:48:17]
goof :
highly recommend you test these carefully and get ready to flick your sport switch if it's coming down too hot
[2017-08-15 07:48:44]
goof :
to stop RTH
[2017-08-15 07:49:02]
goof :
different aircraft will likely have different safe descent speeds
[2017-08-15 07:49:30]
goof :
descent speed appears to switch from param 2 to param 1 around 20-25m off the ground
[2017-08-15 07:52:55]
goof :
also watch for VRS
[2017-08-15 07:53:33]
goof :
if it wobbles too much as it switches to slow speed you'll need to reduce param 2 a bit until it's more stable
[2017-08-15 13:40:21]
carlcox89 :
Thank you man!
[2017-08-15 19:19:47]
oanerm :
Please,how you are making backup of parameters setting in DJI Assistant? Thanks
[2017-08-15 20:11:30]
rainman :
@oanerm Run Ass with debug options, go to Tools, find Backup on top bar of right screen.
[2017-08-15 23:13:50]
oanerm :
thanks
[2017-08-16 23:45:49]
carlcox89 :
anyone knows what this param is ? g_config_landing_smart_landing_vel
[2017-08-17 02:12:28]
goof :
not sure
[2017-08-17 02:13:13]
goof :
perhaps `g_config_auto_landing_vel_L<1-2>` renamed for a different FW?
play around with it in the simulator, see if you can spot a change in aircraft behaviour
[2017-08-17 02:13:38]
goof :
precision landing related maybe?
[2017-08-17 07:26:04]
ender :
yep, sounds renamed. WOnder why they can be so chaotic to have different but same-meaning names even between same generation Firmwares Spark / Mavic…
[2017-08-17 07:26:13]
ender :
(And p4p and whatever)
[2017-08-17 18:34:09]
fred756 :
What is the faster RTH parameter?
[2017-08-17 21:11:46]
fred756 :
Thanks, appreciate it.
[2017-08-18 00:46:17]
carlcox89 :
Thats just horizontal speed tho
[2017-08-18 12:57:17]
fred756 :
yes that's all I need for now, cheers
[2017-08-20 21:07:35]
oqradze :
Hello. very interesting parameters g_config_flying_limit_height_abs_without_gps=30. its default value. I had som problem when I wanted fly at waterfalls. There are very weak GPS signal and my P4P do not fly more then 30 meters height. I tried edit this parameter and I can fly more 30 m when GPS is weak.
[2017-08-20 21:47:51]
kyokushin :
@mavicbreak how to modifiy a max/min/value ? I did it on p3p directly in FC f/w, but i do not know how to get to it in the Spark.
[2017-08-20 21:50:10]
kilrah :
See the wiki.
[2017-08-20 21:53:20]
kyokushin :
i cant find it on wiki. i found only parameters list on assistant
[2017-08-20 21:57:47]
kilrah :
there's a parameter howto
[2017-08-20 21:57:55]
kilrah :
just above
[2017-08-20 21:59:37]
mavicbreak :
@kyokushin I don’t know any way to modify the min/max value. As far as I know the FC does not accept a value on these new drones if it is out of range.
[2017-08-20 22:01:17]
kilrah :
ah that's what you meant
[2017-08-20 22:01:24]
kilrah :
you can change the value, but not min/max
[2017-08-20 22:01:35]
kilrah :
so value needs to be between min and max
[2017-08-20 22:01:53]
kyokushin :
can we change the 'default' value?
[2017-08-20 22:02:07]
kilrah :
nope.. why would you?
[2017-08-20 22:02:15]
kilrah :
that's just what's set after a reset
[2017-08-20 22:02:25]
kyokushin :
by the changin min/max/default we got workaround for NFZ in p3p and heigh limit
[2017-08-20 22:02:39]
kyokushin :
"index" : 428,
"typeID" : 1,
"size" : 4,
"attribute" : 11,
"minValue" : 0,
"maxValue" : 10,
"defaultValue" : 1,
"name" : "g_config.airport_limit_cfg.cfg_search_radius_0",
"modify" : true
[2017-08-20 22:02:53]
kyokushin :
that caused FC to search NFZ in 1 meter radius :smile:
[2017-08-20 22:03:12]
kilrah :
on newer devices you set values with the assistant as the wiki explains
[2017-08-20 22:03:28]
kilrah :
same result
[2017-08-20 22:03:33]
kyokushin :
yes, i know. i though there is a way to change min/max/default
[2017-08-20 22:03:40]
kilrah :
nope
[2017-08-20 22:03:51]
kyokushin :
not exactly same, because radius workaround is not working on newer devices
[2017-08-20 22:04:13]
kilrah :
it's jsut another parameter you need to set
[2017-08-20 22:04:31]
kyokushin :
yes, that parameter also was in p3p, but never checked it
[2017-08-20 22:04:43]
kyokushin :
(because radius worked)
[2017-08-20 22:06:09]
kyokushin :
in never f/w on spark that value is not visible, its working only on .300. I am thinking how to workaround it.
[2017-08-20 22:12:31]
kilrah :
welll yep the solution for that is to stay on 300
[2017-08-20 22:12:34]
kilrah :
:smile:
[2017-08-20 22:12:45]
kilrah :
same as for others (mavic, p4), there's a version to stay on to have that before they removed everything that allowed disabling
[2017-08-20 22:20:43]
kyokushin :
yes, but i am concerned about 'fallingsparkgate'. maybe dji will figure out why spark falling (imo its hardware quality issue, so they cant fix it, only replace/recall), IF its software, then it would be good to raise f/w up.
[2017-08-23 12:47:10]
czokie :
Team: For the next couple of days, I will be out and about. Finishing the last bit of RePL (Remote Pilots License) in Australia. Wish me luck for my tests :slightly_smiling_face:
[2017-08-23 14:36:21]
goof :
all the best for the course finale ^__^ :+1:
[2017-08-24 07:08:33]
czokie :
Passed aroc and theory. Prac tomorrow. Wind forecast not great :(.
[2017-08-26 12:03:22]
carlcox89 :
Anyone tested g_config_go_home_gohome_idle_vel > 10m/s and checked if obstacle avoidance still works with that speed ?
[2017-09-08 17:21:15]
mefisto :
Fyi, param editor will now work with decrypted Mavic FW (it allows changing limits of the parameters). Example:
./dji_flyc_param_ed.py -vv -x -b 0x420000 -m wm220_0306_v03.02.35.05_20170525.pro.bin
[2017-09-08 17:24:53]
weprul0r :
that means you can edit the values before you flash the firmware on the ac?
[2017-09-08 17:26:25]
weprul0r :
got it :slightly_smiling_face:
[2017-09-08 20:31:40]
mefisto :
yes you can change default values, but that's not that exciting. What is more importand is ability to edit LIMITS, ie. fly kilometers up.
[2017-09-08 20:32:23]
mefisto :
with limits modified, you can set values which would otherwise be ignored.
[2017-09-08 20:36:41]
weprul0r :
@mefisto thanks!
[2017-09-08 20:37:52]
weprul0r :
the 500m limit is indeed the first value, which i want to change :slightly_smiling_face:
[2017-09-08 20:41:40]
weprul0r :
is it currently possible to decrypt the latest release 1.3.1000?
[2017-09-09 20:23:08]
mavicbreak :
@mefisto `python3 dji_flyc_param_ed.py -vv -x -m V01.03.0700_Mavic_dji_system.bin
V01.03.0700_Mavic_dji_system.bin: Opening for extraction
V01.03.0700_Mavic_dji_system.bin: Matching parameters array at 0x015389d0: 1 entries, format 2017
V01.03.0700_Mavic_dji_system.bin: Extracting parameters array at 0x015389d0: 1 entries
File “dji_flyc_param_ed.py”, line 454, in flyc_param_get
parprop[‘name’] = fwmdlfile.read(256).split(b’\0',1)[0].decode(‘UTF-8’)
UnicodeDecodeError: ‘utf-8’ codec can’t decode byte 0xe5 in position 3: invalid continuation byte`
[2017-09-10 15:55:35]
mefisto :
@mavicbreak, either wrong module or encrypted. If the array found has only 1 item, that's definitely not it.
[2017-09-10 19:08:14]
kyokushin :
is some f/w of Spark unencrypted?
[2017-09-10 19:45:15]
mavicbreak :
@mefisto thought these bins are not encrypted as the sig files are aes decrypted when pulled from the drone then tarred into bin. What kind of fw should I use to feed dji_flyc_param_ed then?
[2017-09-10 20:08:00]
mefisto :
@mavicbreak m0306, ofc.
[2017-09-10 20:12:45]
tylkologin :
bash-3.2$ ./dji_flyc_param_ed.py -vvv -x -b 0x420000 -m wm220_0306_v03.02.35.05_20170525.pro.fw_0306.bin
wm220_0306_v03.02.35.05_20170525.pro.fw_0306.bin: Opening for extraction
wm220_0306_v03.02.35.05_20170525.pro.fw_0306.bin: At 0x00051c1e, rejected type 26912350 - not known
wm220_0306_v03.02.35.05_20170525.pro.fw_0306.bin: At 0x0006d652, rejected type 1304066744 - not known
wm220_0306_v03.02.35.05_20170525.pro.fw_0306.bin: At 0x000becbe, rejected type 3336757919 - not known
wm220_0306_v03.02.35.05_20170525.pro.fw_0306.bin: At 0x000fd52e, rejected type 3776579961 - not known
wm220_0306_v03.02.35.05_20170525.pro.fw_0306.bin: At 0x0014f4e2, rejected type 1459691195 - not known
wm220_0306_v03.02.35.05_20170525.pro.fw_0306.bin: At 0x00156ffa, rejected type 935848083 - not known
wm220_0306_v03.02.35.05_20170525.pro.fw_0306.bin: At 0x0017107a, rejected type 724443673 - not known
wm220_0306_v03.02.35.05_20170525.pro.fw_0306.bin: At 0x00051c1e, rejected type 14616 - not known
wm220_0306_v03.02.35.05_20170525.pro.fw_0306.bin: At 0x0006d652, rejected type 11147 - not known
wm220_0306_v03.02.35.05_20170525.pro.fw_0306.bin: At 0x000becbe, rejected type 40593 - not known
wm220_0306_v03.02.35.05_20170525.pro.fw_0306.bin: At 0x000fd52e, rejected type 42393 - not known
wm220_0306_v03.02.35.05_20170525.pro.fw_0306.bin: At 0x0014f4e2, rejected type 33976 - not known
wm220_0306_v03.02.35.05_20170525.pro.fw_0306.bin: At 0x00156ffa, rejected type 53941 - not known
wm220_0306_v03.02.35.05_20170525.pro.fw_0306.bin: At 0x0017107a, rejected type 21463 - not known
Traceback (most recent call last):
File “./dji_flyc_param_ed.py”, line 698, in <module>
main(sys.argv[1:])
File “./dji_flyc_param_ed.py”, line 679, in main
flyc_extract(po,fwmdlfile)
File “./dji_flyc_param_ed.py”, line 540, in flyc_extract
raise ValueError(“Flight controller parameters array signature not detected in input file.“)
ValueError: Flight controller parameters array signature not detected in input file.
[2017-09-10 20:13:22]
tylkologin :
Where wm220_0306_v03.02.35.05_20170525.pro.fw_0306.bin is decrypted version of wm220_0306_v03.02.35.05_20170525.pro.fw.sig (from dji_system.bin)
[2017-09-10 20:13:57]
tylkologin :
@mefisto ^ can’t extract json :confused:
[2017-09-10 20:45:28]
kilrah :
it's another encryption
[2017-09-10 20:45:44]
weprul0r :
same error with "wm220_0306_v03.02.40.07_20170817.pro.fw"
[2017-09-10 20:48:31]
weprul0r :
@tylkologin: your file is from fw 900?
[2017-09-10 20:48:48]
kilrah :
<https://github.com/fvantienen/dji_rev/blob/master/tools/image.py>
[2017-09-10 20:55:23]
kilrah :
hmm -900 file indeed, not encrypted
[2017-09-10 20:55:38]
kilrah :
issue is probably getting the base address
[2017-09-10 21:00:32]
kilrah :
or they already changed the whole thing in 900
[2017-09-10 21:02:47]
weprul0r :
indeed the 0306 from 1000 looks still encrypted after decrypting..
[2017-09-10 21:07:17]
kilrah :
did you remove the sig?
[2017-09-10 21:08:47]
weprul0r :
yes
[2017-09-10 21:11:11]
kilrah :
unable to figure it out here either indeed
[2017-09-10 21:17:46]
kilrah :
manually removed the sig though, so might have been done wrong
[2017-09-10 21:18:39]
kilrah :
too tired to get out the mav and dji_verify the thing
[2017-09-11 04:39:11]
tylkologin :
@kilrah yes. i’ve been using image.py from @freaky123 repository. i thought that this tool correctly decrypts .900 sigs.
[2017-09-11 04:40:53]
tylkologin :
because of this error i did another test and downloaded 0306 from @hostile firm_cache (unsigned folder) but result is still the same.
[2017-09-12 01:19:25]
oqradze :
Is tool for linux for editing parameters on P4P?
[2017-09-12 08:00:40]
unusuario128 :
For editing the parameters on the decrypted firmware files, you have to use the phantom_firmware_tools. About modifying the parameters on the drone, you probably need to resort to DUML commands, or maybe you can try to run DJI Assistant with WINE. Also, there is a thing that I didn't try but may work, is to run the Assistant 2 with Electron natively.
[2017-09-13 18:53:21]
hdnes :
Running Electron natively on linux will likely not work because the drivers aren’t written for linux
[2017-09-13 18:53:45]
hdnes :
RINDS will work, but the DUML driver is only for windows and mac
[2017-09-16 20:21:41]
pure3d :
are parameters "raw_bat_level_1" and "raw_bat_level_2" read-only in any fw version?
[2017-09-18 17:04:41]
mefisto :
@tylkologin I only tested it on one FW version; should work on others, but I'm not planning to test that any time soon
I don't own Mavic, so I'm moderately interested in it.
[2017-09-22 23:48:45]
carlcox89 :
@venom-code @quad808
[2017-09-22 23:48:51]
quad808 :
@quad808 has joined the channel
[2017-09-22 23:49:03]
quad808 :
thanks
[2017-09-22 23:49:11]
venom-code :
yes, quad808 when do you plan to do the test?
[2017-09-22 23:49:28]
carlcox89 :
@venom-code what are you trying to say ? I really couldn't understand
[2017-09-22 23:50:10]
venom-code :
even if it works, we still have to choose between force auto land removal at critical battery or faster descent, i think i am more satisfied with removal of forced auto landing at critical battery
[2017-09-22 23:50:47]
quad808 :
not my experience. Both were at 0 on the Mavic, and I just tested it. Let the battery go to 15%, then got low battery warning like normal...went into landing mode in 5,4,3 seconds, so I let it to see what would happen. On my Spark, nothing happens if it is at 0. Mavic went into landing mode, but I canceled it. Sat and hovered to less than 10%, got critical warning...went into landing mode, but I could still control the Mavic, but still wanted to land. Once it went below 5% I couldn't throttle up, landing took over
[2017-09-22 23:50:51]
carlcox89 :
that of course is pilot's choice
[2017-09-22 23:51:28]
quad808 :
I am going to leave L1 at 0, and test L2 setting for increased speed in landing and RTH 1st stage
[2017-09-22 23:52:06]
quad808 :
give me some minutes to test
[2017-09-22 23:52:17]
carlcox89 :
quad808 a good test would be first put L1 at -1 stock and increase just L2
[2017-09-22 23:52:19]
venom-code :
quad808 iam very surprised it hasnt worked for you, did you try to restart AC and RC after tweaking the values to 0?
[2017-09-22 23:52:23]
carlcox89 :
to -5 for instance
[2017-09-22 23:52:33]
carlcox89 :
and press RTH and check if descent speed is -5
[2017-09-22 23:52:33]
quad808 :
k
[2017-09-22 23:52:50]
carlcox89 :
then , wait for it to be on low battery and check both speeds again
[2017-09-22 23:53:37]
venom-code :
i think he already opened dji assistant :stuck_out_tongue:
[2017-09-22 23:54:33]
quad808 :
here is what I have currently...L1 is stock at -1, since I reset it after testing at 0, L2 is -6, but I am going to put that at -7. I will be able to see it right away. LOL
[2017-09-22 23:54:51]
quad808 :
I will report back in a few.
[2017-09-22 23:55:12]
venom-code :
haha just make sure it doesnt come down like a rocket
[2017-09-22 23:55:35]
quad808 :
nah, at -10 it comes down like a rock...lol
[2017-09-22 23:55:47]
quad808 :
be back
[2017-09-22 23:56:04]
venom-code :
-7 is fast just make sure it land on precise position or if you are in an open place so you have time to intervene in case it loses position when coming down fast
[2017-09-22 23:57:13]
venom-code :
-10 was scary fast i feared i might break something on the AC so finally came down to -7
[2017-09-22 23:58:29]
venom-code :
@quad808 i will be here for a while, look forward to your test.
[2017-09-22 23:58:52]
carlcox89 :
:slightly_smiling_face:
[2017-09-23 00:01:11]
carlcox89 :
@venom-code you think changing L1 and L2 doesn't affect RTH descent speed ?
[2017-09-23 00:06:55]
quad808 :
ok, first test...at -7...RTH came down much faster, since it was fighting the prop wash on the way down. Now I am going to increase it to -10...I can always X out...not going to let it come down all the way if it is indeed coming down at -10 LOL...btw...precision landing was spot on at -7, and there is a 10-15MPH wind outside.
[2017-09-23 00:08:51]
carlcox89 :
ok first test it's as I said! Good.
[2017-09-23 00:09:17]
quad808 :
I want it to be silent on the way down, then for sure its at -10
[2017-09-23 00:09:23]
carlcox89 :
increase L2 to -10
[2017-09-23 00:09:28]
carlcox89 :
don't ever increase L1 :stuck_out_tongue:
[2017-09-23 00:09:30]
quad808 :
hang on couple more minutes...yes -10
[2017-09-23 00:09:39]
quad808 :
L1 is stock
[2017-09-23 00:09:42]
carlcox89 :
fine!
[2017-09-23 00:09:44]
quad808 :
Here goes
[2017-09-23 00:09:47]
carlcox89 :
GL
[2017-09-23 00:17:05]
quad808 :
Ok, revising my 1st testing. Changing L2 didn't do squat.
[2017-09-23 00:19:40]
quad808 :
how do I know? My normal speed down is -6, so set at -10 on L2, went into just land mode, came down normal speed. Stopped it...flew out a few hundred feet and about 200' high, did a RTH...started landing at 3mph and watched it...never went higher than that. Cancelled out...dropped the throttle to zero, 12 to 13mph...I know that at -10 in Sport it gets around 24mph straight down
[2017-09-23 00:20:14]
venom-code :
so successful test
[2017-09-23 00:20:16]
quad808 :
so..I say...venom is correct, at least on my Mavic. No change, so this setting must only be for the critical stages of battery
[2017-09-23 00:20:26]
quad808 :
as you said
[2017-09-23 00:20:49]
quad808 :
at -10 it should have come down like a brick
[2017-09-23 00:20:56]
carlcox89 :
weird. I cannot test it now, but for sure will give it another go tomorrow
[2017-09-23 00:21:02]
venom-code :
the whole purpose is we assist and help each other, and i am glad you tested it and did not damage anything
[2017-09-23 00:21:22]
quad808 :
unless you thing I wasn't high enough?? what height does L1 kick in at?
[2017-09-23 00:21:52]
quad808 :
I can re-test
[2017-09-23 00:22:00]
carlcox89 :
L1 is said to kick in at 25-20meters according to nickmv
[2017-09-23 00:22:10]
carlcox89 :
you said you went to 200 feet
[2017-09-23 00:22:24]
venom-code :
L2 to L1 around 20-25m from ground
[2017-09-23 00:22:26]
carlcox89 :
so it appears to be as venom said
[2017-09-23 00:22:56]
quad808 :
it's pretty windy out though...and limited space, but...yes...I was pretty high when I did the RTH at least over 150'
[2017-09-23 00:23:26]
quad808 :
I made a note of the landing speed, so I will try again at stock
[2017-09-23 00:23:33]
carlcox89 :
I only looked at it once and it was at -7 the value I set it too, but it could be me not looking correctly!
[2017-09-23 00:23:35]
quad808 :
should be around 3mph
[2017-09-23 00:23:46]
quad808 :
one more test
[2017-09-23 00:23:48]
venom-code :
200 feet is good enough i think 60 m or so
[2017-09-23 00:23:52]
carlcox89 :
the stock is -3 m/s
[2017-09-23 00:23:54]
carlcox89 :
not mph
[2017-09-23 00:24:14]
quad808 :
I know...I set mine at mph...parameter is different
[2017-09-23 00:24:19]
carlcox89 :
k
[2017-09-23 00:32:33]
carlcox89 :
@quad808 btw, you said "did a RTH...started landing at 3mph and watched it...never went higher than that."
so in RTH it descended at 3mph ?? because that I know for sure that 3m/s is the descent speed of RTH
[2017-09-23 00:33:07]
carlcox89 :
and 3mph is 1.34m/s so something is wrong.
[2017-09-23 00:36:28]
quad808 :
Ok, so this time I made sure to really watch the speeds coming down. All stock settings, except the go home idle is set to 13, which has no effect on landing speed
[2017-09-23 00:38:24]
carlcox89 :
correct
[2017-09-23 00:38:52]
quad808 :
took it up past 150' straight up. Went into land mode, came down steady at around5-6mph, then slowed down to around 3. Stopped it. Took it out and up to 200' and did a RTH...started coming down at 8-9mph, then at round 80 to 100' slowed to around 3mph or so and I let it come all the way in, spot on landing
[2017-09-23 00:40:26]
quad808 :
It is very windy today, so I wonder if that has any effect on anything, but I could definitly see it slow down around 80' or so, then about 20' it slowed again for precision landing adjustments
[2017-09-23 00:41:18]
quad808 :
I will definitely need to test again in calmer conditions
[2017-09-23 00:41:21]
carlcox89 :
so 3mph = 1.34m/s is the descent speed either in land mode/RTH at about 25meters height
[2017-09-23 00:41:49]
quad808 :
I think that is about right, that's L1 right?
[2017-09-23 00:42:06]
carlcox89 :
yes, L1 is -1 stock
[2017-09-23 00:42:23]
quad808 :
ok, makes sense, what is conversion for L2?
[2017-09-23 00:42:50]
carlcox89 :
6.7mph = 3/ms
[2017-09-23 00:43:49]
quad808 :
ok, thats about right...it was fluctuating because of the wind, I am sure of it
[2017-09-23 00:44:21]
carlcox89 :
ok, so both land mode and RTH are having more or less the descent speed = -3m/s, right ?
[2017-09-23 00:44:41]
quad808 :
yes, up higher than L1
[2017-09-23 00:45:14]
carlcox89 :
which could be L2
[2017-09-23 00:45:23]
quad808 :
This reminds me of Arducopter landing settings
[2017-09-23 00:45:57]
carlcox89 :
now if you could try setting the critical battery to a % that's about the current state of your battery, you could try the forced auto landing
[2017-09-23 00:46:09]
quad808 :
same type of thing, but looks like you can't adjust Dji settings, in programmed landing sequence modes
[2017-09-23 00:46:28]
carlcox89 :
and change L2 to -7 or -8 and see if descent speed of forced auto-landing is changed
[2017-09-23 00:47:23]
quad808 :
K, thats a good test! I think it should work, so I will put it at -6 that is plenty fast enough, and L1 0
[2017-09-23 00:47:37]
carlcox89 :
i would change L1 for now
[2017-09-23 00:47:42]
carlcox89 :
*wouldn't
[2017-09-23 00:47:51]
quad808 :
k, safer
[2017-09-23 00:47:54]
carlcox89 :
yup
[2017-09-23 00:48:08]
carlcox89 :
at 0 it could just stop descending at 25meters height
[2017-09-23 00:48:21]
carlcox89 :
i don't think it would just fall :stuck_out_tongue:
[2017-09-23 00:48:36]
quad808 :
I can cancel out of the L2 descent right away, since it is at the low battery warning. I should be able to tell right away from the increased speed down.
[2017-09-23 00:48:50]
carlcox89 :
yeah right
[2017-09-23 00:48:58]
quad808 :
k, off to testing
[2017-09-23 00:49:17]
carlcox89 :
this way we can be sure that this parameter L1 and L2 only affect forced auto-landing descent speed and not LAND / RTH modes
[2017-09-23 00:59:40]
quad808 :
Ok done
[2017-09-23 01:00:07]
quad808 :
I am going to say that in my Mavic, on .700 these settings have zero affect.
[2017-09-23 01:01:22]
quad808 :
Took off at 14% battery...went up past 100'...let it hover and low battery warnings were going off, so I let it go into autoland. No difference in speed than before in land or RTH mode
[2017-09-23 01:01:51]
carlcox89 :
:open_mouth:
[2017-09-23 01:01:57]
quad808 :
Then, X out of that and let it hover, until 10% and critical battery...this is set on stock remember
[2017-09-23 01:02:50]
quad808 :
it automatically went into critical landing mode, but I powered it up past 100'...it was complaining the whole time...I let go of the sticks at 6% battery and watched the speeds...no difference
[2017-09-23 01:03:13]
quad808 :
can't X out of critical battery
[2017-09-23 01:03:45]
quad808 :
We know for sure that .400, safer landing settings at 0, 0 work
[2017-09-23 01:04:11]
quad808 :
I think those settings are overridden at .700, or at least on my Mavic
[2017-09-23 01:04:32]
jcarlo :
Great stuff guys. Don't worry you guys will figure it out soon. Try if you don't succeed, then try again
[2017-09-23 01:04:35]
quad808 :
since I saw no changes at all in descent rate
[2017-09-23 01:04:58]
quad808 :
Need another person on .700 to test and on .400, just to prove the hunch
[2017-09-23 01:05:09]
carlcox89 :
i have 0700 but can only test tomorrow
[2017-09-23 01:05:28]
jcarlo :
I'm on 400. But I won't be able to test it till next week
[2017-09-23 01:05:45]
carlcox89 :
with stock L2 = -3 , first will test LAND mode / RTH Mode invoked by me and watch descent speeds , also test critical landing and see speed
[2017-09-23 01:05:56]
quad808 :
are you guys in Multicopterpilots?
[2017-09-23 01:06:06]
jcarlo :
Also I think gps speed with OA doesn't work on 700
[2017-09-23 01:06:18]
carlcox89 :
then change L2 to -7 and do same test
[2017-09-23 01:06:30]
quad808 :
ahhhhhh...maybe it is OA?
[2017-09-23 01:06:36]
quad808 :
Mine is on
[2017-09-23 01:06:46]
jcarlo :
I'm on multicopter pilots the hidden one:grinning:
[2017-09-23 01:07:03]
carlcox89 :
don't think it's OA related
[2017-09-23 01:07:14]
quad808 :
k, post results there. I can test more this weekend...OA on and off...see if any diff
[2017-09-23 01:07:23]
carlcox89 :
since we bumped gps mode descent and ascend speeds and they work
[2017-09-23 01:07:34]
quad808 :
ahhh...correct
[2017-09-23 01:07:36]
jcarlo :
Ok
[2017-09-23 01:07:37]
carlcox89 :
but good call.. i'll try it both ways
[2017-09-23 01:07:46]
carlcox89 :
OA on and off
[2017-09-23 01:08:15]
quad808 :
at a minimum we will know for sure
[2017-09-23 01:08:47]
quad808 :
I need to get to the field for proper testing and more than one battery...take notes, or screen capture
[2017-09-23 01:09:14]
quad808 :
you get old, you forget within minutes...LOL!
[2017-09-23 01:09:35]
jcarlo :
True
[2017-09-23 01:10:16]
quad808 :
I will start a new thread at Multi and post results today
[2017-09-23 01:13:14]
carlcox89 :
k, i'll try to complete them with another set of runs at 0700 too
[2017-09-23 01:20:24]
carlcox89 :
@quad808 <http://forums.multicopterpilots.com/showthread.php?t=1899&p=7818&viewfull=1#post7818>
[2017-09-23 01:20:37]
carlcox89 :
at least there's another guy that says L1 and L2 do nothing at 0700
[2017-09-23 01:25:09]
carlcox89 :
he also says that at 0700 there's a bug where if you have RTH OBstacle avoidance on but disabled Obstacle Avoidance , the RTH OA wont work :open_mouth:
[2017-09-23 01:30:54]
quad808 :
ok, good find!
[2017-09-23 01:32:12]
quad808 :
and I posted in that thread too...must have missed it, or overlooked it
[2017-09-23 03:36:09]
haloweenhamster :
Just joined noticed @quad808 is a mod but unable to view thread as haven't received activation email yet
[2017-09-23 09:39:28]
triangular :
Sorry if I missed it, but has anyone documented parameter settings possible on latest mavic fw?
[2017-09-23 09:42:53]
kilrah :
If someone did it would be on the wiki...
[2017-09-23 09:44:18]
triangular :
Wiki not updated past 900. Thought somebody has probably taken a peek at params by now. Maybe not.
[2017-09-23 09:45:23]
kilrah :
Don't remember seeing so. Not many of us even bothering with the recent FWs beyond checking for downgradability and encryption...
[2017-09-23 10:54:06]
carlcox89 :
@kilrah you know why auto_landing_L1 and L2 parameter does not have effect on 0700? I thought it should work on all firmware up to 0900
[2017-09-23 10:54:26]
kilrah :
No idea, never tried them.
[2017-09-23 10:54:56]
carlcox89 :
K
[2017-09-23 11:03:40]
carlcox89 :
is there any way to change the simulator parameters ? like i dont want to wait till battery is at X% and could change it to a close value
[2017-09-23 14:59:35]
mavicbreak :
I have the param list for all fw versions can upload it in 6 hours if somebody needs it but I have no time to edit the wiki in this fancy format :)
[2017-09-23 18:11:54]
carlcox89 :
@venom-code ok man, you're right! My apologies !
[2017-09-23 18:11:59]
carlcox89 :
i did all the tests i could do
[2017-09-23 18:12:50]
carlcox89 :
@kilrah it seems one can indeed maneuver aircraft while forced landing is happening :slightly_smiling_face: I did the tests
[2017-09-23 19:01:00]
carlcox89 :
just posted on the topic at <http://forums.multicopterpilots.com/showthread.php?t=1942>
now waiting for moderator approval
[2017-09-23 19:01:15]
carlcox89 :
@quad808
[2017-09-23 19:08:05]
venom-code :
@carlcox89 no need to apologize my friend, we are all here to assist each other in this mission to gain further control over our DJI products :+1:
[2017-09-23 23:38:01]
czokie :
@mavicbreak - Upload the raw param files, and I'll see if I can write a parser to generate wikitext automatically one day :slightly_smiling_face:
[2017-09-24 09:23:42]
carlcox89 :
#here guys Here it is, please check my results regarding RTH/land and forced landing speeds: <http://forums.multicopterpilots.com/showthread.php?t=1942&p=8169&viewfull=1#post8169>
[2017-09-24 09:31:16]
triangular :
Why does that site always give malicious site warnings?
[2017-09-24 11:34:04]
carlcox89 :
Dunno... It runs fine here
[2017-09-24 11:34:21]
carlcox89 :
But I'll paste my findings here
[2017-09-24 11:39:02]
d95gas :
Just been reading this on the forum, you put some work into that :grinning: Nice job and definitely one to add to my archive of useful docs
[2017-09-24 12:18:55]
triangular :
Thanks for the effort, useful info
[2017-09-24 12:20:24]
triangular :
Several times I thought to check out mp forums but I always get numerous malicious warnings from all browsers on all devices, making it difficult to reach the site, as well as concerned over possible javascript threats.
[2017-09-24 13:54:45]
carlcox89 :
:) that took me just 1 1/2 battery .. and if it helps clarify things
[2017-09-24 15:55:11]
carlcox89 :
@triangular i run a simple site scan <https://sitecheck.sucuri.net/results/forums.multicopterpilots.com> and indeed it has something that may affect its visitors.. but I can't figure exactly what it does
[2017-09-24 15:55:51]
carlcox89 :
its called MW:JS:GEN2, seems like some javascript encoded in base64
[2017-09-24 15:56:01]
carlcox89 :
if someone knows what it does, i would appreciate
[2017-09-24 15:58:11]
triangular :
Well if the guy can't run a clean site... then its just too much trouble to bother with.
[2017-09-24 16:27:40]
kilrah :
@flynfrank Any idea?
[2017-09-24 16:27:43]
flynfrank :
@flynfrank has joined the channel
[2017-09-24 17:26:35]
carlcox89 :
I also contacted Frank via pm on his forum...let's see
[2017-09-24 18:41:05]
quad808 :
Hey guys...Porto just posted his findings on MP...here is a copy and paste: Safer Auto Land in FW .700 works!
After previously already gave up trying to make Safer Auto Land to work, I finally found out how to make it work on Mavic FW .700. It was a bit by accident actually, as it came to me when I was doing tinkering with P4P RTH descend speed. I can make the descend speed faster but Precision Landing won't work, or the other way around (it seemed to work randomly, must be a bug in the P4P FW). I initially thought that the default descend speed already maxed out the capabilty of the Precision Landing sensor. But then I thought, what if the descend speed parameter doesn't work because the Precision Landing parameter gets priority?
So, I set the auto land L1 and L2 = 0 and turn Precision Landing off. Viola! It works! Auto Land works in .400 because it has no Precision Landing feature. When we turn Precision Landing on, it gets priority over the normal landing parameter. For me personally, this feature makes .700 even more compelling over .400. Other than the gimbal tilt problem is mostly solved, we can choose to have either Precision Landing or Safer Auto Land simply by turning Precision Landing on or off.
If we don’t need the Safer Auto Land, we can increase L2 landing velocity, turn Precision Landing off, and we can have faster RTH descend (but don’t increase L1 speed. We don’t want hard landing!)
If we need Safer Auto Land, just set L1 and L2 landing velocity to 0 and turn Precision Landing off.
If we need Precision Landing, simply turn Precision Landing on and it will ignore our L1 and L2 landing velocity parameter that we set.
Well, this finding cost me two props and a front landing foot (which not even Thunderdrones sell). I did most of the tests indoor and once didn’t realize I was in ATTI (the room wasn’t bright enough for Vision). But I am happy it works!
Now.... how to force the motors to max out at 80% in Sport mode when having tailwind....
[2017-09-25 17:09:24]
dreadwing007 :
Looks like the Mavic Pro has a hard coded RTH setting if you hit 59K feed one way. Can anyone confirm if there is a way to override this via a parameter setting? .700 Firmware GoApp 4.0.8. Thanks!!!
[2017-09-25 17:34:15]
kilrah :
umm never heard of it - but then it's pretty much impossible to reach that even with battery mods
[2017-09-25 17:38:19]
d95gas :
How the heck you gonna fly 59k ft? thats got to be some modification, especially 1 way :grinning:
[2017-09-25 17:43:38]
dreadwing007 :
it's posisble, but RTH kicks in and you loose all signal.
[2017-09-25 17:46:03]
d95gas :
Interested how? seriously... that's some going
[2017-09-25 17:46:09]
dreadwing007 :
you need powerful antennas and dual battery mod. But when you hit 59K there seems to be some sort of limitation. The P4 has hit over 61K so it's something unique to the MP. I was going to try Flying_Limit_Radius_Limit_Enable=0 as that is the default value on the P4 parameter.
[2017-09-25 17:47:03]
d95gas :
hmmmm dont know.... I have a parameters list I will have a look through and see if there is anything else that might do the job
[2017-09-25 17:47:06]
kilrah :
Even with dual battery seems like a long shot to reach that distance. You sure you're not hitting the critical battery landing?
[2017-09-25 17:47:50]
d95gas :
Have you tried the setting to tell the MP its not a DJI Battery, and you can then tweak that right down (at your own risk)
[2017-09-25 17:47:54]
dreadwing007 :
Here is a flight from a P4
[2017-09-25 17:49:05]
dreadwing007 :
On the MP, if you hit 58,800, then boom instantly no signal. Absolutely no warning and it does a RTH.
[2017-09-25 17:50:27]
dreadwing007 :
This is on a MP with stock parameter settings.
[2017-09-25 17:52:41]
d95gas :
That was going at some speed to achieve that in such a short period of time, long time since my school days at calculating these things, but guess at over 70Kmph
[2017-09-25 17:53:44]
dreadwing007 :
Our FB group sort of specializes in long range flights, but very few are hitting these numbers.
[2017-09-25 17:53:47]
d95gas :
Have a look at telling it non standard battery, and you can then turn down your battery levels, and if I recall, you can knock out the RTH side of it
[2017-09-25 17:54:40]
dreadwing007 :
It's my friends MP, he's going on a record run on the MP, but hitting that limit is a show stopper.
[2017-09-25 17:55:57]
kilrah :
guess you're in uncharted territory here...
[2017-09-25 17:58:00]
dreadwing007 :
LOL, yes!! P4, M600 can all go well beyond the 59K. So something with the MP. We can try a couple things but the goal was to get to 60K on the MP...
[2017-09-25 18:06:53]
carlcox89 :
@dreadwing007 you sure it's not the forced landing thing?
[2017-09-25 18:11:10]
d95gas :
Thats what I was thinking, hence the config change to tell it, its a non standard battery, then change the power warnings to take it to the limit, and I seem to think there was an option to disable that force autoland
[2017-09-25 18:11:23]
d95gas :
would be nice for him to achieve the record though...... braver than me !!
[2017-09-25 18:19:27]
carlcox89 :
Yup change that autoland l1 and L2 parameter to 0
[2017-09-25 18:20:15]
d95gas :
this video might help him get a little extra out of the battery: <https://www.youtube.com/watch?v=BnNo3lWoXkQ>
[2017-09-25 19:37:44]
dreadwing007 :
Thanks guys, I will see if these make a difference.
[2017-09-25 19:38:48]
dreadwing007 :
It's really not a battery issues at least doesn't seem to be as the video completely cuts out at close to 59K.
[2017-09-25 19:39:17]
dreadwing007 :
For those interested in Long range flights, feel free to check out our FB group.
[2017-09-25 19:39:19]
dreadwing007 :
<https://www.facebook.com/groups/faroutmultirotorpilots/>
[2017-09-25 19:39:52]
dreadwing007 :
Just say you are from Slack and i'll approve you
[2017-09-25 20:21:29]
venom-code :
i never registered to fb so cant view your page, but much support to you
[2017-09-25 20:21:45]
venom-code :
are you running a dual battery mod for long range flights/
[2017-09-25 20:22:29]
venom-code :
if yes what batteries are you running on your setup?, hardwired or using an adapter?
[2017-09-25 21:07:46]
carlcox89 :
@channel Did anyone play with sdk_lost_strategy parameter ?
[2017-09-25 21:21:42]
dreadwing007 :
@venom-code Hardwired for maximum efficiency. The is a power clip option, but for max range, hardwired is preferred. Dual MS 4000's. :slightly_smiling_face:
[2017-09-25 21:34:53]
venom-code :
thanks for the reply.
[2017-09-25 21:54:01]
dreadwing007 :
NP, the MP is an incredible long range platform. Even better if it can exceed the 59k feet limitation .-)
[2017-09-25 22:53:56]
venom-code :
@dreadwing007 what exact batteries are you using if you can post a picture of your setup i would appreciate it.
[2017-09-26 01:41:44]
dreadwing007 :
It depends on the flights I'm trying to do. But the Multistar 3000 or 4000 mah batteries are great. (One on each side) People are using either the normal or LiHv packs.
[2017-09-26 01:48:17]
venom-code :
wont a 3000mAh lipo be very heavy for the mavic ? i mean i know you have tested it but just very curious
[2017-09-26 02:06:55]
dreadwing007 :
Not as heavy as dual 4000's
[2017-09-26 02:07:10]
dreadwing007 :
But the MP can handle it.
[2017-09-26 02:07:53]
dreadwing007 :
I'll post some pictures. Should create a thread for Dji mods / battery and range
[2017-09-26 02:31:39]
venom-code :
i will appreciate that, as i was myself looking into ordering a new pair of external batteries for the dual mod, because these other ones i have are meaningless 1500mAh turnigy, one on each side.
[2017-09-26 03:02:20]
dreadwing007 :
Of course!! Start with the lihv 3000s, they are light but be careful when u get to low voltage as the LiHvs do not like to be run down to 0%
[2017-09-26 03:06:07]
pure3d :
@dreadwing007 do the external LiHVs drain at the same rate? When the Mavic battery is down to 10%, how much left do the external LiHVs usually have?
[2017-09-26 03:06:41]
pure3d :
I noticed people with dual 4000s only get like 36-38 minutes total flight time
[2017-09-26 03:55:01]
dreadwing007 :
Normal lipos have a more level curve, and can be flown down to 0%. Do not take the LiHv's anywhere down to 3% or they will drop from the sky.
[2017-09-26 04:01:50]
pure3d :
understood, how about when the Mavic battery is down to 10%, how much left do the external LiHVs usually have?
[2017-09-26 05:02:00]
kilrah :
if the connections are good and the chemistry is similar, they would be in sync
[2017-09-26 17:01:14]
venom-code :
@dreadwing007 yes do post the pics please, above in our conversation you have mentioned 3000/4000mAh Lipos (multistar) i like the 3000mAh multistarts for the dual batt mod, i will be be ordering a pair of these soon.
[2017-09-26 22:54:54]
flydji :
has anyone tried to put the sports mode to cinematic mode. so the side switch would be free for atti mode?
[2017-09-27 00:26:58]
dreadwing007 :
Yes, will post a few pics when I get home. The 59K limitation in the logs show a "OutOfControlGoHome" message
[2017-09-27 00:27:23]
dreadwing007 :
Still need to find a way to disable the auto return home at beyond 59K
[2017-09-27 05:51:37]
b_hargis :
interesting, should be able to trace from that string to where in the logic it occurs unless it is locked inside the FC still. Seems to be protection for a runaway case.
[2017-09-27 12:47:25]
dreadwing007 :
The log messages say 52% battery at maximum distance. So there must be something that triggers a lost connection if X distance is met. The lost connection then forces the RTH. This was on GoApp 4.0.8 and FW .700. Might need to try downgrading the FW to see if the earlier versions exhibit this behavior. On the P4, going beyond 59K works just fine.
[2017-09-27 13:21:15]
czokie :
Dreading. Do it again. But this time set go to meters. And when u think you are approaching the limit, reduce speed to get an accurate number. This might help to look at variable overflow possibilities.
[2017-09-27 15:26:23]
kilrah :
And grab all the logs you can, including system/kernel ones afterwards
[2017-09-27 18:57:08]
dreadwing007 :
:+1::skin-tone-2: I'll grab them. I can throw them on a goggle drive if that helps
[2017-09-27 19:04:31]
quad808 :
I don't have the balls to do long distance flying in my area...too many houses. I barely fly around my neighborhood!
[2017-09-27 19:06:34]
quad808 :
Hmmmmm...maybe have to go out over the ocean...that would work, and little risk if malfunction causes the craft to go down
[2017-09-27 19:14:27]
dreadwing007 :
It's all part of the fun!! Except of it drops in the Ocean :)
[2017-09-27 19:36:23]
venom-code :
it quite a thrill when you are miles away and your signal drops and returns every time and you are getting warning pop ups lol
[2017-09-27 19:38:25]
venom-code :
obviously havent been as far as @dreadwing007 but as far as i could go with my battery mod, its addictive, now every time i put the mavic in the air my heart tells me to go long range otherwise not fun at all
[2017-09-27 21:25:52]
dreadwing007 :
@venom-code Lol, you would for right in on our long range FB group!!
[2017-09-27 21:28:02]
venom-code :
i might register a fb in future just to see and join your long range group, would love to learn from long range experts.
[2017-09-27 21:45:52]
dreadwing007 :
I don't like or use FB other than for the hobby .-)
[2017-10-03 07:16:10]
venom-code :
@dreadwing007 hey man, someone in my neighbourhood is selling a bunch of Multistar 3000mAh LIPOs not LiHV , the batteries are brand new and he is giving them for a cheap price, you think i should buy them for the dual batt mod, as previously i was using the inefficient 1500mAh with not a significant increase in flight times, anyways needed your advice before i bought them, let me know.
[2017-10-04 12:32:14]
codeforge :
hi, what file i need to modify to open dji assistant 1.1.2 with debug=1 and factory_enabled=true ?
[2017-10-04 12:33:42]
czokie :
Not sure if someone has updated it - but have u checked wiki? :slightly_smiling_face:
[2017-10-04 13:01:15]
capra_vecinului :
Hey @codeforge: check out this video digdat0 made: <https://youtu.be/CkpfC56u_ak>
[2017-10-10 08:07:52]
carlcox89 :
@quad808 do you know if firmware higher than .700 the sports+ parameters behave like .400 ? Since we now know that with .700 we cant reach .400 speeds...
[2017-10-10 20:18:43]
quad808 :
Top speed in Sport mode was reduced from .700 on. All the Sport parameters work, but you can't increase top speed unless you are in ATTI mode.
[2017-10-10 21:21:25]
carlcox89 :
k buddy
[2017-10-10 22:31:27]
dreadwing007 :
Yes!! Grab a set for sure!!
[2017-10-10 23:00:30]
venom-code :
ok thanks @dreadwing007
[2017-10-11 13:35:39]
dreadwing007 :
your welcome!! Still trying to break the range limit on the Mavic Pro.
[2017-10-11 13:36:17]
dreadwing007 :
On the P4, M100, M600 there is no limit on the 59K. The m600 can do over 20 miles one way!!
[2017-10-14 00:28:04]
mike4884 :
Im on newest fw for mavic and sport + values stick 55 for tilt gets me 48mph
[2017-10-15 20:51:02]
shammyh :
Not yet... But I have been considering trying to give it a go. The question really is... What exact condition triggers "sdk lost". I fly extensively using Litchi, and with mine set to RTH, I've noticed no RTH behavior when Litchi loses contact with my P4P. Need to setup some simple short waypoint missions (ideally within VLOS waypoint flights in an appropriate environment) and play with it a bit more to see what happens.
[2017-10-19 08:44:31]
dev :
Hi, Im new to the dji_rev, I’m trying to improve the flight time of a P4 using Li-ion batteries.
The Assistant 2 doesn’t let me change **raw_bat_level_1** and **raw_bat_level_2** to lower than 3500. So when the voltage is 13.7v it does an auto-land.
If I keep the throttle up I can continue discharging the battery to 12V. I’m wondering if there is any other params that let me remove that voltage limitation. I’ve tried changing **g_config_bat_config_emergency_voltage** but it doesn’t seem to remove any limitation
[2017-10-19 17:45:04]
mefisto :
@dev if your limit has a limit, you have to unlimit the limit which limits your limit.
[2017-10-19 17:45:56]
mefisto :
the flyc_params have min and max value stored in a binary array within FC firmware.
[2017-10-19 17:47:12]
mefisto :
as long as you have unencrypted FC app firmware, you can change flyc_params limits and default values with this tool:
<https://github.com/mefistotelis/phantom-firmware-tools#dji_flyc_param_edpy>
[2017-10-19 17:49:11]
mefisto :
I did not tested the tool with Inspire, but thet's the same gen as Ph3, so will work.
[2017-10-19 18:09:19]
dev :
thanks @mefisto do you think it can work with the Phantom 4?
[2017-10-19 18:33:17]
mefisto :
Oh, sorry - somehow I got under impression you're talking Inspire. It works on Ph3 and Mavic, so it will likely work on P4 without any modifications needed.
[2017-10-19 20:13:53]
venom-code :
i think he already posted kernel logs on bin4ry request
[2017-10-19 20:14:17]
venom-code :
i cant locate them myself, but i am sure he did
[2017-10-19 20:23:56]
czokie :
did anyone find anything there? I cant remember. I know Binary has been moving house - so may have missed it
[2017-10-20 05:16:32]
kilrah :
I remember many “post next time” and “I will” but no actual post
[2017-10-20 05:38:52]
czokie :
@bin4ry - Did you find anything from the kernel logs re the 58k mavic distance limit thing?
[2017-10-26 13:56:23]
dev :
@haloweenhamster on my tests with a P4 changing it to only led warning the drone will land when battery goes below 14V (I was using a Lithium-ion with 18650cells )
[2017-10-26 13:58:34]
haloweenhamster :
ok, its just that I was having a look around and saw it, haven't tried it
[2017-10-26 13:59:42]
dev :
let me know if you can get it below the 3.5V per cell
[2017-11-15 21:55:56]
mingtao :
it is very easy to get lower than 3.5V
[2017-11-16 07:06:40]
dev :
@mingtao how is it possible to disable RTH or Landing? I’ve seen when the P4 goes a bit below 3.5V there is an automatic landing that I haven’t been able to disable
[2017-11-16 09:25:08]
mingtao :
just set cell battery parameter to 3
[2017-11-16 10:46:08]
dev :
I’ve tried with assistant but I couldn’t. It doesn’t let me to change these params:
[2017-11-16 10:46:16]
dev :
```raw_bat_level_1 3960
raw_bat_level_2 3600
```
[2017-11-16 10:47:44]
dev :
and the params: `g_config_bat_config_bat_limit_limit_vol_min 3300` and `g_config_bat_config_emergency_voltage 3000` don’t seem to prevent an auto-land
[2017-11-16 10:47:59]
dev :
am I missing any other way or params?
[2017-12-01 10:51:45]
mefisto :
anyone tried to understand "global.status"? I can see that it contains bitfields, was wondering whether anyone named the individual bits.
[2017-12-01 23:38:42]
jabuasab :
What's the latest version of the assistant software that allows debug?
[2017-12-01 23:43:00]
weprul0r :
i think V1.1.2-2
[2017-12-11 18:28:43]
oqradze :
Hello is anywhere explanation of parameters? And I want to add parameters list for P4P on wiki page
[2017-12-11 18:31:08]
nocommie :
You mean more than what is already on the wiki?
[2017-12-11 18:31:19]
nocommie :
<http://dji.retroroms.info/howto/mavicallparams>
[2017-12-11 18:31:26]
nocommie :
<http://dji.retroroms.info/howto/parameterhacks>
[2017-12-13 23:07:28]
delone :
Which parameter enables/disables csc mid-air motor shutdowns?
[2017-12-14 18:07:40]
oqradze :
I need more explanetion like second wiki link.
[2017-12-16 06:34:47]
jcarlo :
It seems like the parameter to make gps mode faster id disabled in 4.0000
[2017-12-18 17:32:35]
oqradze :
Yes
[2017-12-20 07:07:28]
acorchia :
is there a setting to disable some notifications? like the ambient light? (i know when i'm flying in the dark)
[2017-12-20 07:21:51]
jcarlo :
@acorchia can't you just turn off the sensors?
[2017-12-20 07:23:32]
acorchia :
i could, it's not ideal
and it jumps out everytime you pass some street light or strong spotlight
[2018-01-08 11:16:56]
haloweenhamster :
Anyone know what the is?
g_config_go_home_adv_gohome_enable
[2018-01-08 21:10:59]
wesleymiller :
precision landing?
[2018-01-12 19:29:28]
codeforge :
how to speed up spark in GPS mode?
[2018-01-12 19:30:04]
codeforge :
i try to change g_config_mode_normal_cfg_tilt_atti_range and others but nothing change
[2018-01-12 19:30:32]
codeforge :
in sport mode spark cannot stabilize gimbal roll and i need it
[2018-01-12 19:36:32]
arrvodesign :
@codeforge another potential thing you can do is turn off the obstacle avoidance … on your own risk
[2018-01-12 19:43:54]
kilrah :
use the “avoid” settings, not “normal”.
[2018-01-12 19:50:20]
codeforge :
I don't know what's the avoid mode, i'm using modded .701 with .300 fw... do i need to change g_config_control_control_mode[1] from 8 to 4?
[2018-01-12 19:50:49]
kilrah :
it’s the set of params the spark uses in gps mode.
[2018-01-12 20:44:22]
codeforge :
thanks guys
[2018-01-30 12:36:53]
dumdedum :
Hi guys. I changed a few parameters in Assistant for my Mavic. This was a few months ago and I did not fly for a while. I have just noticed that when in Sports mode AND when I am not touching the controls, the Mavic slowly rotates by itself. This does not happen in “normal” mode. Any idea which parameter could cause this?
[2018-01-30 15:07:02]
kilrah :
none. but your rc calibration might be off.
[2018-01-30 16:00:03]
dumdedum :
I do have a problem with the RC, the left stick is somewhat broken and won’t hold in place. however this does not affect normal flight. would it be due to the increased rotation sensitivity in sport+ mode?
[2018-01-30 16:06:42]
kilrah :
you got it
[2018-01-30 22:52:47]
validat0r :
who knows what "*_mode_wifi_rc_cfg_*" is?
[2018-01-31 05:39:49]
kilrah :
when connected direct to phone without rc?
[2018-01-31 07:03:16]
djislack :
Or maybe for Spark or Air
[2018-01-31 07:03:30]
djislack :
Since they have wifi controllers, right?
[2018-01-31 07:54:44]
kilrah :
wifi is typically what i said
[2018-01-31 07:55:06]
djislack :
k
[2018-01-31 10:25:17]
dumdedum :
ok thanks.
[2018-02-04 20:16:21]
matthias.loeffel :
hello all! i i modified my spark max altitude parameters, which works fine, but during testing it initiated autoland at 4000ft due to low battery (>65%), which i couldn't cancel. is there a parameter that can be modified to prevent that from happening?
[2018-02-04 20:17:22]
matthias.loeffel :
i'm running mixed .300/.900 firmware
[2018-02-04 20:20:30]
nocommie :
Search for "landing" on this page <https://www.rcgroups.com/forums/showthread.php?2916078-DJI-Dashboard-How-To-tips-and-tricks-%2AMAVIC%2A>
[2018-02-04 20:22:04]
matthias.loeffel :
nice! i guess i found what i need :slightly_smiling_face: thanks a lot!
[2018-03-01 23:59:18]
royeiror :
Anyone know if there's a way to force RAW image capture on Mavic through parameters? The DroneDeploy app keeps changing it to JPG
[2018-03-02 17:59:41]
kilrah :
Parameters are flight controller settings and all related to flight, not the camera or accessories.
[2018-03-02 20:54:45]
royeiror :
Damn, that's sad
[2018-03-02 21:00:06]
kilrah :
you should send a message to that app's support - those apps that change your settings and leave whatever they want instead of backing up your settings and restoring them when exiting are annoying
[2018-03-02 23:10:43]
royeiror :
I have, and they don't recognize it as a problem with their app
[2018-07-28 01:14:51]
will042082 :
Does anyone have any documentation on parameters and what they are for the are?
[2018-07-28 01:28:15]
will042082 :
And like an asshole I forgot to mention the request being for the AIR specifically. I’ve successfully retrieved them and have the min/max etc but didn’t know if anyone has put together what some of them are as they differ from the other models
[2018-07-28 08:10:40]
mefisto :
The only list is on the !wiki.
[2018-07-28 17:25:24]
digdat0 :
there are some for the mavic
[2018-07-28 17:25:32]
digdat0 :
i havent seen the MA list yet
[2018-07-28 17:25:54]
digdat0 :
p4p = same as mavic, inspire 2 = same as mavic, p4 (regular) = slightly different
[2018-07-28 17:26:08]
digdat0 :
p3/1 are there too
[2018-07-28 17:26:47]
will042082 :
Can I post the MA?
[2018-07-28 17:26:57]
digdat0 :
if you can post them i'll look through
[2018-07-28 17:26:59]
will042082 :
I snagged em via websocket last night
[2018-07-28 17:27:01]
digdat0 :
and we can put on wiki too
[2018-07-28 17:27:55]
will042082 :
Ya that’s actually what I meant. Let me clean up the request as it as extra stuff I was playing with. I just reflashed so it’ll all be at default.
[2018-07-28 17:28:55]
digdat0 :
you can put here
[2018-07-28 17:28:56]
digdat0 :
<https://dji.retroroms.info/howto/mavicairparams>
[2018-07-28 17:29:09]
digdat0 :
what fw version?
[2018-07-28 17:33:45]
will042082 :
Latest
[2018-07-28 17:33:52]
will042082 :
01.01.04 or whatever
[2018-07-29 15:45:50]
will042082 :
@digdat0 I’ve added the Air parameters as promised.
[2018-07-29 16:44:29]
will042082 :
Anyone know if auto_gimbal_pitch is the parameter to level on land for the air?
[2018-07-29 16:45:27]
will042082 :
Also. The config_flying_limit_roof_limit_enable =1 is that maybe the air height restriction?
[2018-07-29 19:02:34]
validat0r :
height limit is normally (spark, mavic) done by g_config_flying_limit_height_limit_enabled = 2
[2018-07-29 19:03:16]
validat0r :
air might be different
[2018-07-29 19:05:46]
validat0r :
on recent firmwares you might have to jump through some hoops to change that one ,)
[2018-07-29 19:25:55]
will042082 :
ya air don't have that
[2018-07-29 19:25:57]
will042082 :
just
[2018-07-29 19:26:00]
will042082 :
g_config_flying_limit_roof_limit_enable
[2018-07-29 19:26:01]
will042082 :
and
[2018-07-29 19:26:10]
will042082 :
flying_limit_info_share_limit_enbaled
[2018-07-29 19:27:12]
will042082 :
i'm also convinced that mode_sport_cfg_tilt_atti_range|g_config_mode_sport_cfg_tilt_atti_range is NOT speed/velocity on the air
[2018-07-29 19:27:42]
will042082 :
it DOES seem to change the tilt at which the drone tilts forward when moving, but I don't see a change in top speed
[2018-07-29 19:28:38]
validat0r :
hmm .. ok. it's speed on the spark
[2018-07-29 19:36:26]
will042082 :
Ya 35 or 60. Dudes cracking right over 40 but nothing more
[2018-08-02 14:53:17]
digdat0 :
ive been playing with dji_flyc_param_ed.py with mavic and p4 a bit .. on the p3, i can rename to service filename and load. the newer generation doesnt like that. Curious if anyone is using that to mod the mavic and how your loading the file on the ac.
[2018-08-02 14:54:08]
digdat0 :
i was going to edit, recompile the module and use dumldore. But thought id ask if others have stepped in that water :slightly_smiling_face:
[2018-08-02 15:00:59]
validat0r :
i have only experience with spark, not with mavic and p4. problem is, you have to tamper with processes on the AC to flash a modded flyc fw.
[2018-08-02 15:50:26]
mefisto :
I made the tool, but never tried to flash these on new platforms either.. you need to replace a binary which does the FW verification I assume?
[2018-08-02 16:03:43]
mefisto :
Oh I see now.. you need to re-sign the firmware, but we don't have a key - so re-sign with a custom crafted key.
[2018-08-02 16:04:03]
mefisto :
And then you have to convince the AC that your key is legit.
[2018-08-02 16:04:16]
validat0r :
that's one possibility
[2018-08-02 16:05:52]
validat0r :
but since you're already on the ac, you could just yank out the whole verification process .. i guess
[2018-08-02 16:06:29]
mefisto :
yeah, that's a solution too. A bit more prone to mistakes, I guess..
[2018-08-02 16:07:03]
validat0r :
i guess dji would argue tampering with the fw is the first mistake to make
[2018-08-02 19:17:03]
digdat0 :
thanks guys. I'm sure that ripping out that verification woudl be beyond me, but i'll dig into what mefisto noted about re-sign with a key and then convince the ac the key is legit.
[2018-08-02 19:18:45]
validat0r :
I dont agree
[2018-08-02 19:20:55]
digdat0 :
well, let me state that differently .. I am scared at bricking my mavic lol .. it would be my 4th core board. That said, if i knew where to look id def start.
[2018-08-02 19:21:33]
digdat0 :
it seems that either looking at prevenitng the key validation, disabling it .. thinking outloud, adb into the device and then find the right area to start tweaking
[2018-08-02 19:21:42]
validat0r :
bricking while tampering is always possible
[2018-08-02 19:24:17]
digdat0 :
need a low cost core board distributor :stuck_out_tongue:
[2018-08-15 19:21:26]
007 :
Hello.
How can i change the parameters in p3s ?
With the cs 2000 flashing works ?
Thanks
[2018-08-29 21:40:16]
validat0r :
doesnt assistant2 1.1.2 in debug mode work?
[2018-08-29 21:40:26]
validat0r :
@shacharmilo..
[2018-08-29 22:52:50]
lolo780 :
On a p3?
[2018-08-30 10:16:18]
mefisto :
It requires some determination, but may work. Hardware is compatible.
[2018-08-30 10:16:36]
mefisto :
Anyway you can just use firmware tools.
[2018-08-30 18:30:38]
validat0r :
g_config.landing.smart_landing_by_1860_enable
[2018-08-30 18:30:55]
validat0r :
anyone knows what this param is referring to?
[2018-08-30 19:09:24]
mefisto :
Lc1860 is not a flight controller, so i would assume this allows the leadcore chip to influence landing
[2018-08-30 19:10:46]
validat0r :
sure. on spark it's set to 0, on other birds/older FWs to 1 .. so I was wondering in what kind of situations the 1860 would want to initiate a SL
[2018-08-30 20:10:32]
kilrah :
maybe precision landing
[2018-08-31 08:18:11]
capra_vecinului :
Anyone connected a M2P to the DJI Assistant Version 1.1.0-2 (aka the first one with the "extended parameter settings")?
[2018-09-06 01:29:48]
lolo780 :
I can't get mine to connect to do parameters.
[2018-09-06 02:41:01]
poopnondji :
Use assistant 1.1.2 it's working for me
[2018-09-06 03:51:57]
lolo780 :
Damn, must be something up with my computer then
[2018-09-12 17:58:00]
007 :
Hi guys.
Which frimware on p4p v1 i need to downgrade for using on NFZ and altitude unlimit ?
Thanks
[2018-09-12 18:01:13]
cantrepeat :
1.05.0600 for DJI Phantom 4 Pro
[2018-09-12 18:01:26]
cantrepeat :
<https://github.com/o-gs/DJI_FC_Patcher>
[2018-09-12 18:09:51]
007 :
Thank.
There is an instractions for how to use that FC Patcher ?
[2018-09-12 18:16:53]
cantrepeat :
The link to the github has the instructions
[2018-09-12 18:36:04]
007 :
TNX.
[2018-09-14 13:46:36]
007 :
Hi.
Someone can tell me why i can't see the number of % on my p4p rc ? It's a new one. The rest looks like ok.
Thanks
[2018-09-14 13:55:10]
007 :
Sorry, % of battery.
[2018-09-14 19:48:26]
lolo780 :
Non dji battery?
[2018-09-15 05:14:01]
007 :
yes
[2018-09-15 12:49:25]
007 :
Thanks Lolo 780, i returne to int. Battery and it's works now.
Thanks.
[2018-09-15 12:57:10]
kilrah :
it’s normal, non-dji battery precisely disables everything but voltage display.
[2018-09-15 13:01:38]
007 :
Tnx
[2018-09-15 16:02:14]
validat0r :
With spark there is still percentage
[2018-09-15 16:08:37]
cantrepeat :
Even with dual battery mod?
[2018-09-15 16:09:04]
cantrepeat :
I think that was his issue, dual battery mod, battery_type 2 and no % display
[2018-09-15 17:11:05]
007 :
Right with Spark i didn't get that issue.
But now in the p4p it's display.
[2018-09-16 05:04:15]
lolo780 :
Set battery type to 3 and you'll get % display
[2018-09-16 05:05:16]
lolo780 :
<https://youtu.be/JFMyBTioc3M>
[2018-09-16 05:05:25]
lolo780 :
Looks like that.
[2018-09-16 05:10:03]
007 :
The standart battery type is 4, no ?
[2018-09-16 05:11:40]
007 :
I get the battery % back after i change back to the int. Dji battery.
[2018-09-16 05:39:48]
007 :
Can i change the battery on non int. Dji from type 4 to type 3 and to see the % on p4p ?
[2018-09-16 10:51:20]
lolo780 :
Stock is type 1
[2018-09-16 10:51:37]
lolo780 :
Works on p4p
[2018-09-16 10:51:58]
lolo780 :
Gets rid of auto landing
[2018-09-16 10:53:37]
007 :
Change that type from rc or dji assi
[2018-09-16 10:54:57]
007 :
With or without the parameter bat. -1 & -3
[2018-09-16 10:55:22]
cantrepeat :
@lowellfoo780 Hey I noticed in your video your HD is not flashing like in most other videos I see. Any idea what cause it to flash?
[2018-09-16 10:58:53]
lolo780 :
Not sure
[2018-09-16 11:00:22]
lolo780 :
<https://youtu.be/QnFan0xeNFY>
[2018-09-16 11:00:36]
lolo780 :
I think theres a few flashes in this one
[2018-09-16 11:06:46]
cantrepeat :
OK, seems there are two signals, the radio one for control and the HD which indicates the strength of the signal for the video feed.
[2018-09-16 11:08:24]
cantrepeat :
Are you on an android or iphone device?
[2018-09-16 14:53:15]
lolo780 :
Android
[2018-09-16 16:23:50]
kilrah :
flash is "external interference detected"
[2018-09-16 16:23:57]
kilrah :
aka noisy environment
[2018-09-20 02:02:45]
739461411 :
How to set the parameters of 4p 2.0, then you can fly at nfz ,and the specified altitude.The geo Can I set it?i set nfz parameters 0 to 1,but still can't fly .anyone who can tell me ,thanks .
[2019-02-06 16:51:19]
marijus75 :
Hi. What Spark's parameter/-s have to be changed in NLD Client to get smoother yaw movement? There are many parameters including the word "yaw". Has only the basic_gain_yaw which is set to 50 (min 20, max 100) to be reduced, or more parameters also have to be changed?
[2019-07-03 02:23:53]
venom-code :
what exactly does this parameter do: g_config_control_avoid_atti_range
[2019-07-03 02:31:44]
venom-code :
and if battery is set to non dji, do i still have to change the g_config_landing_auto_landing_vel_L1 and L2 to = 0 to avoid auto landing during low/critical battery?
[2019-07-03 04:28:20]
digdat0 :
yes to the battery question, setting to non-dji will allow you to not have to change the parameter to 0 to prevent autolanding.
[2019-07-03 04:30:22]
digdat0 :
on the parameter, there are two:
g_config_control_avoid_atti_range = 16
g_config_avoid_cfg_avoid_atti_range = 15
These are the tilt angles for obstacle avoidance (OA). The one with "control" in it is GPS mode using OA. I always assumed the other was if GPS failed in OA mode, basically ATTI with OA enabled.
[2019-07-03 04:30:31]
digdat0 :
Curious to think that others have seen too!
[2019-07-03 12:27:45]
venom-code :
thanks man
[2019-07-03 17:35:58]
quad808 :
so @digdat0 just to be clear for my notes. If you set battery to non-dji, in order to avoid critical low battery kicking in, is that the only thing you need to change as a minimum, or do you need to change like the following:
[2019-07-03 17:36:52]
quad808 :
I have never tested the above settings and don't know if they are overkill
[2019-07-03 18:02:51]
venom-code :
@quad808 trying to flash your custom 01.04.0300a from the Matoupi section of DDD slight confusion this is a .tar file while the rest are almost all .bin files, there is also Brett8883's versions of the same file but in .bin, i tried flashing it all went well but in the go app the height limit cannot be decreased from 9000m its like hardcoded typed in red so wanted to try your version instead but slightly caught up with the .tar instead of .bin, how do i go about it
[2019-07-03 19:50:10]
quad808 :
You can just change the .tar to .bin
[2019-07-03 19:50:44]
quad808 :
You should be able to easily change the 9000 limit...do you have NLD GO?
[2019-07-03 20:35:11]
venom-code :
no bro patched a 4.1.22 go
[2019-07-04 01:26:47]
brett.e.burkhart :
I think Dumldore will flash a tar file anyway but yea I haven’t been having any luck with the 9000m thing. Interested to see if @quad808’s version works for you or if @quad808 you are able to get the standard or non NLD patched 4.1.22 to do it too. Have had no one who can replicate
[2019-07-04 02:58:46]
digdat0 :
i only ever change the battery type = 2 (or non-dji in assistant). I move the sliders down to the lowest voltage as well. So that would also be raw_bat_level_1 and raw_bat_level_2. I dont touch the other things, i believe type2/non-dji overrules the other settings. Except in cases like p4 where it shows 0%, will set to type 3.
[2019-07-04 02:58:54]
digdat0 :
and never had any complaints :slightly_smiling_face:
[2019-07-04 19:12:59]
brett.e.burkhart :
I notice if you leave the dji intelligent battery but turn off force rth and force landing it STILL will not allow you to enter a intelligent flight mode if the low battery warning has gone off. Could have like 40% battery remaining and not be able to go into tripod mode which sucks
[2019-07-04 19:16:16]
brett.e.burkhart :
I also wouldnt change the auto landing speed to -10 thats crazy will give you a heart attack each time. If you want to do that you should maybe consider raising the level2 landing height. I dont think these auto-landing parameters apply to smart landing btw. theres a smart battery landing vel or something like that too
[2019-08-07 23:09:47]
dronepilot :
Hi guys. Any way to lower M1P rpm? Thanks
[2019-08-08 05:24:32]
brett.e.burkhart :
Fly slower or get higher pitch props
[2019-08-08 17:23:34]
brett.e.burkhart :
Yea
[2019-09-07 04:45:10]
venom-code :
this parameter alters the OA distance/range : g_config_control_avoid_atti_range, but i am trying to know what does this one do : g_config_avoid_obstacle_limit_cfg_safe_dis , if someone can shed some light please
[2019-09-07 06:25:00]
brett.e.burkhart :
You have it backwards safe_dis is OA distance range.
[2019-09-07 06:26:48]
brett.e.burkhart :
_atti_range is tilt (speed)
[2019-09-07 06:47:37]
venom-code :
sorry my bad bro pasted the wrong parameter wrong place in the sentence :stuck_out_tongue:
[2019-09-07 06:47:40]
venom-code :
thanks for letting me know
[2019-09-13 16:04:29]
brett.e.burkhart :
Avoid_mode refers to GPS mode with the front sensors turned on so that parameter g_config_control_avoid_atti_range
Refers to max tilt (speed) with the front sensors on.
There’s also a parameter g_config_control_control_avoid_atti_range
That also is for max tilt with front sensors on. I believe one of them has to do with the tilt at which you get a warning that the front sensors are turned off due to breaking the attitude limit for the front sensors to be active.
Could be wrong about that though.
[2019-10-12 16:43:30]
jackmax :
Which P4P parameter value is used to turn the visual positioning below on and off？
[2019-10-12 20:38:57]
brett.e.burkhart :
Try g_config_misc_cfg_vps_func_en
[2019-10-13 06:41:36]
brett.e.burkhart :
See there’s your problem. By definition there’s no positioning hold in Atti mode...
You are trying to force OPTI mode it sounds like which is P-GPS mode without GPS or that’s how you have to think about it.
Don’t think of it as ATTI mode plus VPS, that’s where you done gone wrong. You need to turn OFF GPS mode not turn ON VPS.
g_config_gps_cfg_gps_enable=0
and keep VPS turned on like normal
[2019-10-27 13:14:51]
dronepilot :
Mavic Air compass calibration how to uncheck this when starting motor won’t start.
Thanks
[2019-11-18 01:36:32]
papareproductora :
Hello! Is there any way to turn off the gimbal motors by parameters in mavic 1 pro? Thank you!
[2019-11-24 22:22:26]
oakley75 :
Any way to enable the dev mode on newer (after 1.1.2) assistants? Main.js changed to "toggle dev tools", obviously different than the older electron. Ctrl-shift-I doesn't work. I assume we should still be about to adjust max speed rate down and maybe a few other parameters on the newer stuff nowadays...
[2019-11-24 22:40:28]
validat0r :
Parameter page isn’t in the code any more
[2019-11-24 22:42:08]
validat0r :
Would love to have a GUI to change parameters
[2019-11-24 22:42:19]
validat0r :
Or an app
[2019-11-25 16:12:02]
funnel :
in utils.js remove everything from banDevTools -> banDevTools: function(e, t) {}, and uncomment devtools in main.js
[2019-11-25 23:19:23]
oakley75 :
Wow will try that this evening on v1.2.5
[2019-11-25 23:25:38]
oakley75 :
Utils.js not present on the 3 different assistants I have installed, inc 1.1.2b. I guess that's what @ilovemynexus4 was talking about?
[2019-11-25 23:25:58]
validat0r :
did you unpack the app.asar?
[2019-11-25 23:26:52]
validat0r :
Assistant 1.1.2 can be easily patched so the development stuff is accessible
[2019-11-25 23:27:14]
validat0r :
that's documented
[2019-11-25 23:28:06]
validat0r :
and afaik Assistant 2 ver 2.xxx don't have development pages in their code any more
[2019-11-25 23:28:45]
validat0r :
i could be wrong .. but no one convinced me of the contrary so far
[2019-11-25 23:30:04]
validat0r :
i tried to run the app.asar of 1.1.2 on Assistant 2 2.xxx, which works to a degree, but is a whole different mess
[2019-11-26 01:01:52]
digdat0 :
@denisgithub555 did you also need to alter the ac specific JS Files? They all call utils.banDevTools(), Im wondering if simply removing it from utils.js is enough?
[2019-11-26 11:23:45]
oakley75 :
I'm just getting started playing in electron and damn it's interesting
[2019-11-26 11:28:02]
validat0r :
OK. Try to plug the old app.asar into ass 2.0
[2019-11-26 11:28:23]
validat0r :
Or maybe just the parameter page. That would be awesome.
[2019-11-26 13:57:43]
asdrubale :
No is not enough I try to delete bandevtools but doesn’t function . Ps I unpack Asar , I modified the file package to read without asar file, I added opendevtool but nothing ....I just arrive here (also force already debug variable to 1 without window .
[2019-11-26 13:59:54]
asdrubale :
Doesn’t function
[2019-11-26 14:02:08]
validat0r :
yeah .. lots of hash errors
[2019-11-26 14:02:24]
validat0r :
would require some major refactoring i guess
[2019-11-26 14:46:16]
asdrubale :
This is the maximum that arrive
[2019-11-26 14:46:31]
asdrubale :
But still not ok
[2019-11-26 15:09:33]
validat0r :
if you plug the app.asar of 1.1.2 into 2.0 you get much more .. the whole range of additional pages, but they dont work properly. funny thing: changed parameters are showing nicely, but you can't alter them, nor see the unaltered ones
[2019-11-26 16:29:41]
validat0r :
g_config.landing.exit_landing_ground_not_smooth_enable
[2019-11-26 16:30:00]
validat0r :
this one is awesome .. how does it detect this anyway? :smile:
[2019-11-26 16:30:27]
validat0r :
had it once the other day, and ground wasn't smooth alright
[2019-11-27 06:37:22]
asdrubale :
Already tested but put old app.asar 1.1.2 in new 2.08 or 2.010 not function....also because you cannot see the mini (the target that we have) , I also try all the wm160 of 2.010 into 1.1.2 debug version....but nothing if we want try we need to work on 2.010or 2.08 but mixing with old i think that we cannot succeed ...we need to found the right mod sw in 2.010 or 2.08 and than introduce the file of wm160 on 2.08
[2019-11-27 09:41:56]
funnel :
I can't help you more than that. I understood you just needed the right dev window appear.
[2019-11-27 19:51:10]
loli88ie :
Hi guys, i try for mavic mini with python this:
python comm_og_service_tool.py com4 -vvv WM160 FlycParam set g_config.flying_limit.max_height 20 --alt
But dont work
[2019-11-27 19:51:23]
loli88ie :
[2019-11-27 19:52:46]
loli88ie :
My mini up over 20 meter
[2019-11-27 20:18:38]
validat0r :
you can set this with the app, you know?
[2019-11-27 21:16:11]
loli88ie :
I did it to test the method, I thought it would block the maximum altitude at 20 meters even if I lifted it from the app.
is there a list already tested for the mavic mini?
[2019-11-27 21:17:21]
validat0r :
a list containing what?
[2019-11-27 21:25:45]
loli88ie :
Parameteres tested
[2019-11-27 21:26:54]
validat0r :
I tested some I modded on my spark .. but I don't know of a list
[2019-11-27 21:27:25]
validat0r :
you can pull a list of all params of the mini with comm_of_service_tool
[2019-11-27 21:27:29]
validat0r :
and try yourself
[2019-11-27 21:28:56]
validat0r :
i did sport mode+, gps mode+, bat mod
[2019-11-27 21:30:11]
validat0r :
more concerned with "fcc" modding, bc my CE mini is very much limited by the poor RF capabilities
[2019-11-27 21:30:56]
validat0r :
I bet there'll be a nice black market for FCC minis in CE countries
[2019-11-27 21:32:49]
loli88ie :
I have mini fcc
[2019-11-27 21:32:58]
validat0r :
lucky you
[2019-11-27 21:33:00]
loli88ie :
Thank you for information
[2019-11-27 21:34:36]
validat0r :
@loli88ie -> pm
[2019-11-28 14:14:44]
asdrubale :
Some people can help me to update this line for mini mavic ? dji_flyc_param_ed.py -vv -x -b 0x0000 -m wm230_0306_v01.00.02.255_20170213.bin (this was for air)
[2019-11-28 23:43:50]
mingtao :
Are you decrypted 0306 module for MM?
[2019-11-28 23:44:12]
mingtao :
Without decrypto no way to help you
[2019-12-02 00:59:28]
loli88ie :
Hi guys, i change in my mini this :
Mode sport:
Rc scale 1
tilt angle 45
Vert up 7. Work
Vert down -7. Work
Brake 60. Work
Tors gyro 180
But Max speed is limit 13m/s
what parameter is missing for the maximum speed?
[2019-12-08 11:03:28]
heresmydron :
Ill try that today. Silly question, are you modifiying these params on linux or windows? Can get the AC to appear as a usb device in linux. I have to do it via VM, open assistant and then run comm_og_service_tool.py
[2019-12-08 11:04:25]
heresmydron :
nvm just saw your screenshot. guess ill have to continue using a vm :F
[2019-12-11 06:38:12]
monkeyman :
hi, any idea to detech com port on mac ?
[2019-12-11 06:38:39]
monkeyman :
I’ve use /dev/cu.usbmodem143103 but unfortunatelly not match wkwkkw
[2019-12-11 06:39:26]
monkeyman :
ioreg -p IOUSB -l -b | grep -E “@|PortNum|USB Serial Number”
[2019-12-11 06:39:41]
monkeyman :
+-o WM160@14310000 <class AppleUSBDevice, id 0x100000840, registered, matched, active, busy 0 (51 ms), retain 26>
“PortNum” = 1
“USB Serial Number” = “123456789ABCDEF”
[2019-12-25 22:45:27]
markusfriedl :
<https://github.com/Ace-Code1/commOgServiceGUI/tree/master/build> to use comm_og_service_tool.py more easily with multiple AC's
[2019-12-25 22:46:43]
validat0r :
great work ..
[2019-12-25 22:46:50]
validat0r :
trying it on linux right now
[2019-12-25 22:51:10]
validat0r :
I get Error on retrieving value
[2019-12-25 22:51:15]
validat0r :
not sure, why
[2019-12-25 22:52:12]
validat0r :
is there a verbose/debug switc?
[2019-12-25 23:01:30]
markusfriedl :
you should see some output when starting it from the console... it is a very first draft and need some additional love
[2019-12-25 23:01:55]
validat0r :
right .. i'm installing eclipse right now
[2019-12-25 23:02:07]
validat0r :
dont see output on the console ..
[2019-12-25 23:02:23]
markusfriedl :
will defintely have to increase the amount of logging
[2019-12-25 23:02:31]
validat0r :
access to /dev/ttyACM0 needs root privileges ..
[2019-12-25 23:03:29]
markusfriedl :
ah understand... just tested it on windows today
[2019-12-25 23:04:30]
validat0r :
yeah, on win ordinary user privs are enough for com port acces
[2019-12-25 23:15:41]
b1tninja :
maybe a grid view for the values
[2019-12-25 23:24:33]
validat0r :
will have a look at it in the next days on linux :smile: that's for the headway
[2019-12-26 07:34:41]
markusfriedl :
appreciate all support there to make it more userfriendly ;)
[2019-12-26 11:05:19]
markusfriedl :
@ilovemynexus4 i quickly added some additional logging and updated the Readme file... hope you figure out how to get the Ports working on Linux :slightly_smiling_face:
[2019-12-26 12:26:27]
validat0r :
Will try later
[2019-12-28 16:03:08]
monkeyman :
failed to get config for g_config_control_control_mode_0 maybe different with mp2
[2020-01-08 15:13:31]
mel69hash :
Anyone kind to share the 2 debuged DJI Assistant 2 for older version for MP & M2P. I've messed up mine when I install the official Assistant 2. Fuck DJI.
[2020-01-08 15:17:03]
heresmydron :
does anyone know whats the parameter name to increase the downward speed on the mini? thanks :slightly_smiling_face:
[2020-01-08 16:03:05]
pingspike :
@mel69hash I can send you **DJI Assistant 2 v1.1.2** - any use?
[2020-01-08 16:03:30]
pingspike :
fucking stupid DJI version naming conventions
[2020-01-08 16:04:59]
pingspike :
next thing you know they'll be naming drones with Phantom 4 Pro V2 or Inspire 1 V2
oh...
wait...
[2020-01-08 21:33:34]
markusfriedl :
g_config.mode_sport_cfg.vert_vel_down_0 and vert_vel_down_adding_max_0
[2020-01-09 09:56:02]
heresmydron :
thanks
[2020-01-18 19:37:30]
trulala69 :
Anyone familiar with comm_og_service_tool? How do I get/set parameters for different flight modes? If I do a get I only get the value for mode_normal...
[2020-01-18 19:53:38]
digdat0 :
something like this should get the entire list: comm_og_service_tool.py /dev/ttyUSB0 MAVIC FlycParam list --start=1 --count=1200 --fmt=csv
[2020-01-18 19:54:41]
digdat0 :
and then a similar command to this to edit the value on that specific parameter for the other flight mode. you need to find the parameter you want to modify. comm_og_service_tool.py /dev/ttyUSB0 -vv MAVIC FlycParam set g_config.flying_limit.max_height_0 500
[2020-01-18 19:55:05]
digdat0 :
that is, replace g_config.flying_limit.max_height_0 with the parameter and 500 with the proper value
[2020-01-19 07:04:16]
trulala69 :
Thanks, I‘ll give this a try...
[2020-01-19 10:23:33]
mel69hash :
@rich great. Pls DM me or shae it here if allowed. Thank Bud
[2020-02-14 17:08:09]
dronepilot :
Hi guys i have a friend M1P that doesn’t work the vps, everything is calibrated on dji assistant 2.
The vps camera shows on calibration.
On flight it doesn’t hold position and doesn’t show the front sensors.
No error message on the app and did a fresh firmware to make sure nothing was wrong on that.
Any help
[2020-02-14 17:08:26]
dronepilot :
Sorry on the posta at general
[2020-02-27 04:24:31]
djimod :
How do you know what the proper count is? How high should I go?
[2020-02-29 19:37:59]
digdat0 :
not sure. set the count= very high, then examine the output file in the CSV and see what the top limit is. Each aircraft have differnet number of paramters in my experience
[2021-03-21 18:28:57]
tobimimer :
Since there are a lot of parameters available on the DJI Mini 2, is there a parameter to modify the peep sound of the controller (ie. disable it)?
[2021-03-21 19:22:03]
heresmydron :
are you talking about when you press the buttons or the RTH beeping?
[2021-03-21 20:02:55]
validat0r :
hot glue
[2021-03-22 10:57:29]
tobimimer :
Yeah RTH beeping is an example. It also peeps on startup or low battery. I would disable all of that if I could. Hot glue isn't an option for me.
[2021-03-22 11:09:44]
validat0r :
@jan2642 did SilencioRC back in the days. <https://dufo.be/silencio/> maybe you can persuade him to upgrade to work with Mini 2
[2021-03-22 11:11:27]
tobimimer :
SilencioRC-0.9.4.exe? :D
[2021-03-22 11:12:28]
validat0r :
yes. it's legit. AFAIR it works with Mavic Pro.
[2021-03-22 11:13:14]
validat0r :
he patched the 0600 module of the firmware.
[2021-03-22 12:45:55]
mefisto :
some beeps stop if you press the power button (one, short press). But for some this has no effect.
This is so annoying.
[2021-03-22 14:52:19]
validat0r :
yeah .. I endured the RC bat low beep once for quite some time only to have it shut down by a simple power button press after like 10 minutes :smile:
[2021-03-22 14:52:53]
validat0r :
RTH beep doesnt shut up sadly
[2021-03-22 20:30:27]
heresmydron :
battery_type_0 0 disables beeping, but also disables all warnings
[2021-03-23 03:56:44]
djibot.5150 :
Open remote, snip speaker wire, close remote?
[2021-03-23 09:31:14]
mefisto :
Path, not wire. But yeah, that's doable. You could even put a small resistor there to just decrease volume.
[2021-04-02 09:47:33]
tobimimer :
@heresmydron "battery_type_0 0 disables beeping, but also disables all warnings" What warnings?
[2021-04-03 07:16:15]
heresmydron :
on the app. you wont get the "50% battery down, better come back" warning
[2021-04-03 07:16:47]
heresmydron :
also the app will only show the "time until depleted". Time to RTH and time to forced landing will show up as 00:00
[2021-04-03 07:17:09]
heresmydron :
just pay attention at your battery levels and youll be fine, ive been flying with battery type 0 since day one and no accidents (so far)
[2021-04-03 11:48:35]
tobimimer :
Thanks!
[2021-04-03 14:54:29]
djibot.5150 :
Actually that resistor idea is a good one, I'll do that next time I have my M2P remote open. Thanks
[2021-04-26 03:55:21]
oakley75 :
Concerning parameter changes to remove MP1 autolanding, what does the auto_landing_vel_L2 at value -6 accomplish exactly?
[2021-04-26 07:56:30]
validat0r :
I think it increases the vertical vel in rth to 6m/s at higher altitudes.
[2021-04-26 17:16:13]
quad808 :
g_config.landing_auto_landing_vel_L2 = -10 (-3)*this is speed of auto landing above 20m. -10 is maximum descend speed. Changing this parameter means that if you want to RTH and descend at a fast rate quickly and not have to do this manually, set this to a high rate. All birds can take a setting of -10 and be fine, but the heavier birds may be best at -8. If you set this at 0, even if you do a RTH, the bird will go above home point, but will not descend and will just sit there.
[2021-05-29 13:03:09]
oqradze :
Which firmware need for edit NFZ for Inspire 2?
[2021-06-01 16:41:11]
the.hope.ltd :
Hello
I have mavic 2 z wich is not linking to rc
Update always ask for missing updating meduals
The link led on ac stay red even after pushing
Any idea for sulotion
Or where is the rf board on core board of m2??
[2021-09-21 09:33:48]
flyhigh213 :
Does know of a site with listed all the Mavic 2 Zoom / Pro parameters anywhere? Since DH the only ones I see mentioned are mainly for battery type, and rth surprised its still red and not started / complete on retroroms.
[2021-09-21 16:54:50]
quad808 :
there are hundreds if not thousands of parameters
[2021-09-21 17:26:20]
mefisto :
Work on a list started, but there are no contributors.
<https://dji.retroroms.info/howto/parameterindex>
[2021-10-12 23:16:29]
fun.day.cool :
does anyone have a text file with what all the parameters do on the air 2?
[2021-10-13 08:07:54]
heresmydron :
<https://github.com/444A49/ma2findings>
[2021-10-28 15:25:34]
eddy :
eddy joined the channel.
[2021-10-30 04:06:38]
crushedice2000 :
crushedice2000 joined the channel.
[2021-10-30 09:12:39]
powellste :
powellste joined the channel.
[2021-10-30 12:15:19]
jj :
madmaqx joined the channel.
[2021-10-31 00:21:18]
will :
will joined the channel.
[2021-10-31 21:11:13]
lazypilot :
lazypilot joined the channel.
[2021-11-01 05:46:11]
ambushbug :
ambushbug joined the channel.
[2021-11-02 00:33:21]
amanita :
amanita joined the channel.
[2021-11-03 06:17:26]
fly2high213 :
fly2high213 joined the channel.
[2021-11-03 16:04:39]
deesparkom2 :
deesparkom2 joined the channel.
[2021-11-05 15:25:01]
dave0x6d :
dave0x6d joined the channel.
[2021-11-10 16:50:20]
aszeszo :
aszeszo joined the channel.
[2021-11-12 10:45:52]
cs2000 :
cs2000 joined the channel.
[2021-11-12 10:45:56]
cs2000 :
dji-rev-bot added to the channel by cs2000.
[2021-11-12 10:46:00]
cs2000 :
@cs2000 left the channel.
[2021-11-16 15:50:23]
alex1234 :
alex1234 joined the channel.
[2021-11-24 23:06:46]
kimberlyisaflake :
kimberlyisaflake joined the channel.
[2021-12-06 23:27:43]
aol :
aol joined the channel.
[2021-12-07 10:34:39]
galbb12 :
galbb12 joined the channel.
[2022-01-18 00:50:34]
il1oo0 :
il1oo0 joined the channel.
[2022-01-25 13:53:04]
masskrug :
masskrug joined the channel.
[2022-02-08 09:11:42]
uliraudel :
uliraudel joined the channel.
[2022-03-03 15:14:48]
gh :
ghartabc joined the channel.
[2022-03-22 20:03:21]
cds :
cds joined the channel.
[2022-03-24 00:45:14]
fredmicrowave :
fredmicrowave joined the channel.
[2022-03-24 01:30:56]
anethema :
anethema joined the channel.
[2022-03-30 11:23:56]
windoze :
windoze joined the channel.
[2022-04-27 16:10:25]
cds :
@cds left the channel.
[2022-05-22 09:42:49]
jack117wb :
jack117wb joined the channel.
[2022-05-23 06:33:06]
superlogical :
superlogical joined the channel.
[2022-05-23 20:46:02]
jjbyrnes29 :
jjbyrnes29 joined the channel.
[2022-05-24 17:26:01]
h_marshall :
h_marshall joined the channel.
[2022-05-26 14:22:57]
item1979 :
item1979 joined the channel.
[2022-05-31 19:00:27]
emeraldmaster :
emeraldmaster joined the channel.
[2022-06-20 06:26:03]
bgiovanny :
@bgiovanny left the channel.
[2022-06-27 01:16:24]
airsheen :
airsheen joined the channel.
[2022-06-30 17:33:39]
zorast :
zorast joined the channel.
[2022-06-30 17:36:46]
zorast :
Did someone know whait this does? Changing the Voltage level 2 to 3500 and set this to 0/2 will expand flight time? Air2s:
[2022-06-30 17:37:38]
zorast :
Probably changing this settings does not have mutch differrence, it still does show red circle about 10% rest Battery in FlyApp. When changing this Settings on my Mini3Pro it works well and does only show a litte read circle about 1% in FlyApp. Any solution here for gettings this protect setting down to 0-3% ?
[2022-06-30 17:41:17]
fabyo :
fabyo joined the channel.
[2022-06-30 17:43:22]
zorast :
@fabyo which mini 3 parameter want u change ?
[2022-06-30 18:04:11]
speatuk :
speatuk joined the channel.
[2022-06-30 18:46:05]
quad808 :
Things to remember about parameter settings. Parameters is how you can turn things on and off, increase settings within a range set by DJI. Because of the way the firmware works, and because way back the OG's figured out how parameters worked, we could create our own firmware and "owned" the DJI firmware. You could create custom firmware and make your Mavic Pro a mean, fast little drone. Can't do this anymore....you have to live within the parameters that DJI allows you to change, and even that......they don't like you changing anything. They (DJI) realized what people were doing and locked down the firmware from most parameter changes, and hid the really good ones like turning off NFZ and altitude enforcement. Sad to say, until the firmware is totally "owned" again and we an roll our own, have to live within the DJI limitations of min/max on what they "allow" you to still change on your drone.
[2022-06-30 18:59:45]
areoc :
areoc joined the channel.
[2022-06-30 19:12:26]
dereksynkopa :
dereksynkopa joined the channel.
[2022-06-30 19:44:39]
dereksynkopa :
Instead of Cine mode, I turned on ATTI mode because I enjoy flying in this mode a lot more. Unfortunately, I noticed that in the ATTI Mode, it is practically impossible to climb the drone up during the flight. Speed has to drop significantly, sometimes even to zero in order to be able to ascend, this is very disappointing. There is no such problem in the mini 2. I wonder what parameter is responsible for this.
[2022-06-30 21:28:34]
tmbinc :
tmbinc joined the channel.
[2022-07-01 05:42:31]
nz-maori :
nz-maori joined the channel.
[2022-07-04 13:00:59]
robertosmera :
robertosmera joined the channel.
[2022-07-06 16:06:54]
stanlee :
stanlee joined the channel.
[2022-07-06 18:30:26]
airiver :
airiver joined the channel.
[2022-07-09 18:22:09]
d95gas :
d95gas joined the channel.
[2022-07-15 17:53:05]
xou :
xou joined the channel.
[2022-08-15 19:07:24]
sergey.muhlynin :
sergey.muhlynin joined the channel.
[2022-09-26 01:12:57]
jackmax :
jackmax joined the channel.
[2022-10-15 01:28:55]
richter08 :
richter08 joined the channel.
[2022-10-29 17:21:14]
bojangles :
bojangles joined the channel.
[2022-11-13 20:42:16]
eseven :
eseven joined the channel.
[2022-11-21 18:56:37]
dereksynkopa :
Has anyone managed to find the parameter in the fpv settings that is responsible for the font size in the subtitles of the srt file? Size 28 is unacceptable. Of course, I can convert it later on the computer, but that's extra work.
[2022-11-21 22:05:07]
kilrah :
parameters have always been about the flight controller, nothing about the camera, accessories etc is in there.
[2022-11-21 22:05:07]
kilrah :
parameters are about the flight controller, nothing about the camera, accessories etc is in there.
[2022-11-22 09:19:36]
dereksynkopa :
Probably a lot in this right, but you can set other things, such as turning off the led, ToF and others. Thanks.
[2022-11-22 09:29:22]
areoc :
How can I make the motors start one by one
[2022-11-22 10:19:57]
kilrah :
yeah, all stuff controlled by the FC :)
[2022-12-09 15:53:47]
ivar :
ivar joined the channel.
[2022-12-24 20:12:24]
gaijin :
gaijin joined the channel.
[2022-12-27 15:58:38]
baxove :
derowey joined the channel.
[2022-12-27 16:24:47]
baxove :
Hello! Is there any way to increase the descent speed on DJI Mini 2? It does not seem to have the parameter g_config.mode_sport_cfg.vert_vel_down, only for tripod and normal
[2022-12-29 08:20:27]
tmbinc :
There used to be pm_mode_sport_cfg mode_sport_cfg_vert_vel_down (it doesn't seem to have a g_config. alias... does that mean it's not externally settable?) but it's clipped to -3.5 which I think is already the default.
[2022-12-29 08:20:54]
tmbinc :
So I think the workaround is to use "gentle" mode, where mode_gentle_cfg_vert_vel_down can be up to -10
[2022-12-29 08:22:39]
tmbinc :
but there's also a dynamic part based on add_vert_vel_down_adding and vert_adding_factor
[2022-12-29 08:22:45]
tmbinc :
(Which I don't think is configurable)
[2022-12-29 08:29:50]
kilrah :
had looked into it at release and even gentle didn't work, you could set it higher but it still wouldn't go faster, probably clipped at a lower level
[2022-12-29 08:30:01]
kilrah :
not aware of changes around that lately
[2022-12-29 08:32:43]
tmbinc :
It's clipped to vert_vel_down_adding_max
[2022-12-29 08:32:53]
tmbinc :
pm_mr_sa_mission_cfg_t.vert_vel_down_adding_max
[2022-12-29 08:33:26]
tmbinc :
It defaults to -3.5, but range is -10..0
[2022-12-29 08:35:24]
tmbinc :
[2022-12-29 08:36:01]
tmbinc :
vert_vel_down points to &final_param.vert_vel_down i.e. the resulting vert_vel_down
[2022-12-29 10:24:16]
baxove :
Thank you for the answers. I've tried changing the mode_gentle_cfg_vert_vel_down and vert_vel_down_adding_max, but it didn't seem to have any increase in descent speed when flying in gentle mode. Maybe it's clipped somewhere else or I've missed something. The parameters I changed:
g_config.control.control_mode[0] = 6
mode_gentle_cfg_vert_vel_up = 6
mode_gentle_cfg_vert_vel_down = -8
vert_vel_down_adding_max = -10
mode_gentle_cfg_rc_scale = 0.95
mode_gentle_cfg_tilt_atti_range = 35
mode_gentle_cfg_tors_gyro_range = 100
This seems to work on the Mavic Air 2, https://github.com/444A49/ma2findings,
but I had no luck with those parameters on my DJI Mini 2 unfortunately.
[2022-12-31 21:20:53]
trueandfalse :
spartaksm99 joined the channel.
[2023-01-01 17:18:10]
trueandfalse :
@spartaksm99 left the channel.
[2023-01-07 17:14:12]
efwefaf :
efwefaf joined the channel.
[2023-02-04 10:46:19]
dereksynkopa :
Today I made flights checking the new possibilities of the mini 2 drone. With a fairly strong wind, I must say that the drone behaves wonderfully. Here are some conclusions: the climb, despite the setting at 10m/s, could not be made due to air resistance and strong wind. The fastest climb was 8 m/s, the wind at the top measured in the ATTI mode was 16 m/s. But going down is pure poetry. Stable -10m/s no jerking and no vibration. I was wondering about the lack of possibility to fly in gentle mode at speeds greater than 5m/s and it seems unnecessary. I have it set to 1 m/s. This meant that the drone did not struggle to maintain its position in the air and did not use energy unnecessarily. Yes, it is blown away by the wind, but it doesn't matter at this point. What's important is that it's going up fast. I also turned on the "...close_auto_stop_motor_check" parameter to check if there might be a "navigation system error" when driving at a speed greater than about 20km/h, but it does. I used to get the same error when I tested falling down with engines off in autorotation. This prevents the in-flight engines from starting when falling down. If this could be turned off, it would be possible to descend at 16m/s with the heavier 3500mah battery. What do you think about it?
[2023-03-02 00:10:35]
ibndias :
ibndias joined the channel.
[2023-03-05 12:27:36]
efwefaf :
Can anyone use this to unlock the DJI T40 battery and modify the number of cycles
[2023-03-23 18:05:26]
dronez4u :
dronez4u joined the channel.
[2023-03-24 17:51:10]
efimato_re :
efimato_re joined the channel.
[2023-04-08 06:12:04]
gudvin :
gudvin joined the channel.
[2023-04-08 06:14:05]
gudvin :
@gudvin left the channel.
[2023-04-13 02:56:14]
retrocall :
retrocall joined the channel.
[2023-04-28 10:33:47]
supertester :
supertester joined the channel.
[2023-05-10 22:17:44]
stanlee :
There used to be a parameter:
bat_enable_smart_bat_landing_protect
[2023-05-10 22:17:57]
stanlee :
I can't find it anymore. I'd set it to 0 to stop forced landing.
[2023-05-10 22:18:04]
stanlee :
What can I do instead?
[2023-05-10 22:24:55]
lolo780 :
What drone?
[2023-05-10 22:37:44]
stanlee :
M3 Pro
[2023-05-10 22:38:04]
stanlee :
I thought it would be the same as the M3.
[2023-05-10 22:38:40]
stanlee :
Wonder what param I can change to prevent auto landing.
[2023-05-10 22:39:04]
stanlee :
Is there a comparable param for the other models that prevents auto landing?
[2023-05-10 22:39:07]
lolo780 :
Hmm. I haven't flown my M3 below 10% yet
[2023-05-10 22:39:24]
lolo780 :
What FW?
[2023-05-10 22:39:36]
stanlee :
@lolo780 thanks in advance, you are a legend!
[2023-05-11 00:49:51]
stanlee :
The latest fw on the M3Pro. v01.01.0100
[2023-05-11 00:49:51]
stanlee :
The latest fw on th eM3Pro. v01.01.0100
[2023-05-11 00:57:44]
lolo780 :
I was working on a M3 Cine on fw 1100. I needed to reboot with DJI assistant first before being able to connect with DH.
[2023-05-11 02:33:14]
stanlee :
Is the "bat_enable_smart_bat_landing_protect " parameter gone for you as well?
[2023-05-11 02:34:02]
stanlee :
I can connect to DH just fine. That parameter just
seems gone
[2023-05-11 02:34:06]
lolo780 :
It's there. I'll be seeing some M3Ps soon and will check.
[2023-05-11 02:34:39]
stanlee :
Ok. Yeah- it doesn't appear on the M3P as far as I can tell.
[2023-05-11 02:34:57]
stanlee :
There are some new battery params but I don't want to mess with them.
[2023-05-11 02:35:07]
stanlee :
Thanks Lolo
[2023-05-11 02:37:12]
lolo780 :
I have an M3 Cine arriving soon that spent 10 days in the rain up a tree in Costa Rica. I'm curious if a non cine can accept the SSD
[2023-05-11 08:14:14]
tmbinc :
You'd need to transplant the PCIe header onto the core board
[2023-05-11 08:14:48]
lolo780 :
Oh
[2023-05-11 08:15:12]
tmbinc :
How bad does the Cine look? :)
[2023-05-11 08:15:26]
tmbinc :
10 days sounds back but it depends no what kind of rain and how long it was powered
[2023-05-11 11:01:52]
lolo780 :
I did some waterproofing on it before the shoot but it has some power system error. With luck it's just an ESC board.
[2023-05-11 14:37:21]
oakley75 :
@stanlee haven't seen this name in a hot minute :v:
[2023-05-11 15:40:30]
stanlee :
Ha!!! Been quietly lurking. I'm back in the game now :)
[2023-05-12 08:57:07]
lolo780 :
Mavic 3 firmware 1000 resets auto landing parameters every time you boot. 900 seems fine.
[2023-05-12 19:46:23]
stanlee :
Gotcha.
[2023-05-12 19:46:55]
stanlee :
Weird that the battery param just disappeared.
[2023-05-17 11:41:30]
joelg :
joelg joined the channel.
[2023-05-17 11:44:45]
joelg :
what do i need to do to increase decent speed on my air2s? changed it to 8m/s in drone hacks but doesn't seem to make a difference
[2023-05-17 15:53:36]
lolo780 :
Try the NaN hack
[2023-05-17 16:58:17]
tmbinc :
Has the NaN hack be successfully used on non-Mini 2 yet?
[2023-05-17 16:59:28]
lolo780 :
I think it works on Mini 3 Pro
[2023-05-19 05:54:51]
joelg :
NaN hack?
[2023-05-19 06:26:05]
lolo780 :
[2023-05-19 06:57:40]
joelg :
has anyone tried this before on air2s?
[2023-05-27 05:22:01]
drmsucks :
drmsucks joined the channel.
[2023-05-27 14:21:28]
lishujian3 :
lishujian3 joined the channel.
[2023-05-29 01:39:56]
revnmavic :
revnmavic joined the channel.
[2023-05-31 22:18:36]
nicksapienza :
nicksapienza joined the channel.
[2023-06-11 01:12:42]
milenovic :
milenovic joined the channel.
[2023-06-14 14:14:23]
lorebene99 :
lorebene99 joined the channel.
[2023-06-14 14:15:30]
lorebene99 :
Good afternoon,
I am Lorenzo, a student from Italy, Genova, who, together with three other students, is currently developing a project in the field of robotics engineering. In summary the objective of the project is to develop a software to manage UAV fleets autonomously from a ground control station. At this stage of the project we are working with DJI Mini 2 drones and we managed to have more than one drone autonomously flying waypoint missions loaded from PC using the RCs as a bridge between the PC and each drone, in particular to do so we are using Rosetta Drone running on the smartphones connected to the RCs (an open source Github project) and QGroundControl as GCS on the PC. For the next step we would like to transfer what is done by Rosetta on the PC, communicating with the drones using an external antenna connected to the PC, but to do so, keeping the possibility of taking manual control when the RCs are turned on (for safety reasons), we need to have the drones working even without RC, which is now not possible. If you have any advice we would be grateful.
[2023-06-14 14:15:30]
lorebene99 :
Good afternoon,
I am Andrea, a student from Italy, Genova, who, together with three other students, is currently developing a project in the field of robotics engineering. In summary the objective of the project is to develop a software to manage UAV fleets autonomously from a ground control station. At this stage of the project we are working with DJI Mini 2 drones and we managed to have more than one drone autonomously flying waypoint missions loaded from PC using the RCs as a bridge between the PC and each drone, in particular to do so we are using Rosetta Drone running on the smartphones connected to the RCs (an open source Github project) and QGroundControl as GCS on the PC. For the next step we would like to transfer what is done by Rosetta on the PC, communicating with the drones using an external antenna connected to the PC, but to do so, keeping the possibility of taking manual control when the RCs are turned on (for safety reasons), we need to have the drones working even without RC, which is now not possible. If you have any advice we would be grateful.
[2023-06-15 12:26:25]
revnmavic :
Anyone worked on the battery settings, Maybe where if the percentage is so low it auto powers down?
[2023-06-26 19:31:45]
joelg :
So has anyone been able to increase decent speed on the air2s? Using the gentle mode hack or the nan hack maybe?
[2023-07-03 19:47:26]
harryemery92 :
harryemery92 joined the channel.
[2023-07-03 20:01:09]
anzz :
anzz joined the channel.
[2023-07-24 03:05:35]
dji-rev.concierge132 :
dji-rev.concierge132 joined the channel.
[2023-08-01 13:52:02]
crashing_bird :
crashing_bird joined the channel.
[2023-09-13 10:15:01]
molda :
molda joined the channel.
[2023-09-17 19:59:56]
johndohn :
johndohn joined the channel.
[2023-10-06 12:22:17]
lorebene99 :
Sorry, do you know at which frequency rate the radio controller sends the commands to the drone? (Drone: Matrice 210 RTK V1). Thank you!
[2023-10-08 02:24:01]
revnmavic :
Anyone tried to read or change the params on the mini 4 pro yet?
[2023-10-15 20:50:09]
dumldore_newbi :
dumldore_newbi joined the channel.
[2023-10-23 09:15:54]
jdan7387 :
jdan7387 joined the channel.
[2023-10-24 17:35:21]
caseygibson :
caseygibson joined the channel.
[2023-10-29 10:58:20]
alex7593 :
alex7593 joined the channel.
[2023-11-02 13:25:16]
dhsacxz :
dhsacxz joined the channel.
[2023-11-12 15:37:44]
jester_j :
jester_j joined the channel.
[2023-11-19 13:51:51]
flylusive_pat :
flylusive_pat joined the channel.
[2023-11-24 08:03:18]
s1m0n :
s1m0n joined the channel.
[2023-12-24 10:37:58]
sparkyws :
Enabling Atti mode on an Air 3 (fswitch_selection|g_config_control_control_mode[0] = 3) works great but it seems to be limited to 68mph
Does anyone know why and can be it overridden
[2024-01-17 09:47:26]
photogrant :
photogrant joined the channel.
[2024-01-17 17:29:34]
s1m0n :
On witch FW Version U Changed the Parameters for Air3? All the time, i Change and save the Parameters, nothing is Changes... I'm on fw 01.00.0300
[2024-01-18 15:44:08]
basilius :
basilius joined the channel.
[2024-01-24 05:42:52]
efwefaf :
Does anyone need the US version of DJI T30 T40
[2024-02-06 14:06:24]
xpk :
xpk joined the channel.
[2024-02-06 19:59:27]
ryantkasher :
ryantkasher joined the channel.
[2024-02-10 03:22:30]
accountfrompl :
accountfrompl joined the channel.
[2024-02-12 20:44:42]
lining-preps.0u :
lining-preps.0u joined the channel.
[2024-02-14 16:35:45]
otter :
otter joined the channel.
[2024-02-24 11:44:19]
efwefaf :
Does anyone need a DJI T50 that can fly globally
[2024-02-24 16:28:15]
dkovar :
OK, ask in one channel, not every one.
[2024-03-04 18:23:45]
klarensky :
klarensky joined the channel.
[2024-04-13 17:52:11]
the_mini2_guy :
the_mini2_guy joined the channel.
[2024-04-13 23:52:02]
the_mini2_guy :
Hi! is it possible to completely disable the GPS using one of these parameters? (DJI mini 2 ) - https://wiki.dji-rev.com/howto/mini2params
[2024-04-14 00:48:01]
the_mini2_guy :
And in general, is there a guide about what each parameter does? and what is worth changing?
[2024-04-17 09:21:32]
s1m0n :
As far as I know, GPS cannot be changed via the parameters. Otherwise it depends on what you want to achieve... e.g. the StelthMode (lights off), faster up/down, no automatic RTH when battery is empty, warning of empty battery only later (10, 5%), height of hover mode, Atti Mode, Acro Mode and a few other things
[2024-04-17 13:17:59]
kilrah :
you can disable GPS on several models, probably doesn't do what you expect though
[2024-04-17 13:18:14]
kilrah :
the one i always turn off is the "smart landing"
[2024-04-20 13:38:14]
oakley75 :
Sadly, manual mode died years ago. You could try aluminum foil. Kinda silly I know, but I hear it's functional (for the most part).
[2024-05-14 14:12:17]
symza :
symza joined the channel.
[2024-05-21 07:01:44]
wag-on :
wag-on joined the channel.
[2024-05-22 02:30:28]
caracara :
caracara joined the channel.
[2024-06-03 14:50:09]
devinnorgarb :
devinnorgarb joined the channel.
[2024-06-22 22:42:09]
qr25 :
qr25 joined the channel.
[2024-07-01 17:30:25]
mrsmith :
mrsmith joined the channel.
[2024-07-01 22:54:29]
blandreth94 :
blandreth94 joined the channel.
[2024-07-17 03:02:54]
propz :
propz joined the channel.
[2024-07-26 15:52:58]
theguac :
theguac joined the channel.
[2024-07-26 15:53:51]
ogini_ayotanom :
ogini_ayotanom joined the channel.
[2024-08-22 14:39:01]
swaggyc :
swaggyc joined the channel.
[2024-08-22 18:35:49]
clait :
clait joined the channel.
[2024-08-31 15:44:40]
zar1n :
zar1n joined the channel.
[2024-10-07 18:42:34]
tokertm :
tokertm joined the channel.
[2024-10-21 01:53:13]
supermario7331 :
supermario7331 joined the channel.
[2024-12-13 01:34:20]
david2212 :
david2212 joined the channel.
[2025-01-05 10:08:26]
grizzfu :
grizzfu joined the channel.
×
User Info
Username:
Last Login:
First Name:
Last Name: